toasters

toasters@lists.teaparty.net

2 participants
13529 discussions

Re: [RE]Weird autosupport problem
by David McWilliams 23 Jul '08

23 Jul '08

No problem. We tried http, https & smtp, but no real difference. Sláinte, David Give a man a fire and he's warm for the day. But set fire to him and he's warm for the rest of his life. - Terry Pratchett, Discworld On Wed, Jul 23, 2008 at 12:32 PM, oakley <oakerz(a)lycos.com> wrote: > No disrepect intended, but are you sure you changed it to SMTP? Looking at > the output you have below, autosupport.support.transport is set to HTTP and > not SMTP. > > - Mike > > > > ---------[ Received Mail Content ]---------- > > Subject : Weird autosupport problem > > Date : Wed, 23 Jul 2008 11:40:43 -0400 > > From : "David McWilliams" <davidkmcw(a)gmail.com> > > To : "NetApp list" <toasters(a)mathworks.com> > > > > Autosupport worked fine up until about six weeks ago, no it doesn't. We > > can't think of anything that changed in the environment. > > > > We can ping the mailserver, I tried telnetting to the mailserver on port 25 > > to see if it is still relaying, seems to be OK. We weren't seeing any > > messages at all regarding autosupport in the messages file, an time we > > tested. We just changed the transport to smtp, from https, and we now get > > one message, but that's all, see below. > > > > netapp2050a> df -h > > > > Filesystem total used avail capacity Mounted on > > > > /vol/rootvol/ 20GB 197MB 19GB 1% /vol/rootvol/ > > > > /vol/rootvol/.snapshot 0TB 0TB 0TB ---% > > /vol/rootvol/.snapshot > > > > > > netapp2050a> options autosupport > > > > autosupport.cifs.verbose off > > > > autosupport.content complete > > > > autosupport.doit DONT > > > > autosupport.enable on > > > > autosupport.from netappalert(a)###.com > > > > autosupport.local.nht_data.enable off > > > > autosupport.local.performance_data.enable off > > > > autosupport.mailhost 10.1.1.130 > > > > autosupport.minimal.subject.id hostname > > > > autosupport.nht_data.enable on > > > > autosupport.noteto > > helpdeskteam(a)###.com > > > > autosupport.performance_data.enable on > > > > autosupport.retry.count 15 (value might be overwritten in > > takeover) > > > > autosupport.retry.interval 4m (value might be overwritten in > > takeover) > > > > autosupport.support.enable on > > > > autosupport.support.proxy > > > > autosupport.support.to autosupport(a)netapp.com > > > > autosupport.support.transport http > > > > autosupport.support.url support.netapp.com/asupprod/post/1.0/postAsup > > > > autosupport.throttle on > > > > autosupport.to > > admin(a)###.com > > > > > > From the messages file > > > > Wed Jul 23 11:04:38 EDT [netapp2050a: asup.general.drop:error]: Out of > > messages for autosupport, skipping autosupport: USER_TRIGGERED (test) > > > > The machine is running 7.2.2L1. Does anyone have any ideas? > > > > Sláinte, > > > > David > > > > Give a man a fire and he's warm for the day. But set fire to him and he's > > warm for the rest of his life. > > - Terry Pratchett, Discworld > >

1 0

Weird autosupport problem
by David McWilliams 23 Jul '08

23 Jul '08

Autosupport worked fine up until about six weeks ago, no it doesn't. We can't think of anything that changed in the environment. We can ping the mailserver, I tried telnetting to the mailserver on port 25 to see if it is still relaying, seems to be OK. We weren't seeing any messages at all regarding autosupport in the messages file, an time we tested. We just changed the transport to smtp, from https, and we now get one message, but that's all, see below. netapp2050a> df -h Filesystem total used avail capacity Mounted on /vol/rootvol/ 20GB 197MB 19GB 1% /vol/rootvol/ /vol/rootvol/.snapshot 0TB 0TB 0TB ---% /vol/rootvol/.snapshot netapp2050a> options autosupport autosupport.cifs.verbose off autosupport.content complete autosupport.doit DONT autosupport.enable on autosupport.from netappalert(a)###.com <netappalert(a)plastipak.com> autosupport.local.nht_data.enable off autosupport.local.performance_data.enable off autosupport.mailhost 10.1.1.130 autosupport.minimal.subject.id hostname autosupport.nht_data.enable on autosupport.noteto helpdeskteam(a)###.com<jlalik@plastipak.com,helpdeskteam@plastipak.com> autosupport.performance_data.enable on autosupport.retry.count 15 (value might be overwritten in takeover) autosupport.retry.interval 4m (value might be overwritten in takeover) autosupport.support.enable on autosupport.support.proxy autosupport.support.to autosupport(a)netapp.com autosupport.support.transport http autosupport.support.url support.netapp.com/asupprod/post/1.0/postAsup autosupport.throttle on autosupport.to admin(a)###.com<lkostoff@platipak.com,bblair@plastipak.com> From the messages file Wed Jul 23 11:04:38 EDT [netapp2050a: asup.general.drop:error]: Out of messages for autosupport, skipping autosupport: USER_TRIGGERED (test) The machine is running 7.2.2L1. Does anyone have any ideas? Sláinte, David Give a man a fire and he's warm for the day. But set fire to him and he's warm for the rest of his life. - Terry Pratchett, Discworld

3 2

mounting a volume on windows machine from a linux machine using ssh
by Anna M 22 Jul '08

22 Jul '08

I have a windows 2003 server where I have set up an ssh service. Now I want to mount a filer volume there. I can execute normal commands using ssh on that windows machine from my linux boxes but I can not successfully execute mount/ net use commands. Every time I try it, I get error: The local device name is already in use. Though I can execute same commands using rsh. Any clue whats wrong here? -- View this message in context: http://www.nabble.com/mounting-a-volume-on-windows-machine-from-a-linux-mac… Sent from the Network Appliance - Toasters mailing list archive at Nabble.com.

4 3

snapvault start question
by Romeo Theriault 21 Jul '08

21 Jul '08

I'm just starting to test snapvault and I have a few questions about it's usage that I haven't found sufficient answers for in the documentation. I'm hoping someone might be able to help explain them to me. * On the snapvault start command you can specify your source (primary) dataset by these three different options. 1. filer:/vol/volname/qtree_name - for a particular qtree 2. filer:/vol/volname/- - for non-qtree data in a volume 3. filer:/vol/volname - for contents of entire volume including all qtrees. My question is, "Is there any difference between options 2 and 3, if I don't have any qtrees in any of my volumes?". Second question is in regards to a note in the snapvault documentation that states: "7.2.3 Volume to Qtree SnapVault When issuing the snapvault start command, you are not required to specify a qtree name for the source; however, this practice is not recommended. This type of relationship increases the performance of the SnapVault transfer; however, it also increases the amount of time it takes to perform a backup. Since you must specify a qtree for the SnapVault destination, an entire volume then resides in a qtree on the destination. When it's time for the restore via the Data ONTAP CLI, the entire contents of the qtree, which contains all the data from the source volume, is restored to a qtree on the SnapVault primary system. Once the data is restored, you must then manually copy the data back to the appropriate location." As I've eluded to in my question above, we don't use any qtrees in our environment. Is the above note saying that when I do a snapvault restore that it's going to restore back into a qtree and I'll have to manually copy the contents out of the qtree back into the root dir of the volume before it will be back to the way it was before the restore? I'm hoping that's not what it's saying, though it sure sounds like it. Thanks for any help on this, Romeo

3 3

RANDOM Questions
by ifstat 17 Jul '08

17 Jul '08

Hi I have a few random question regarding the FAS3170 and Data ONTAP 7.2.3. 1. Does netapp support IBM 3583 Tape Library or has anyone successfuly configure a FAS system with this library? 2. What are the maximum number of volumes that you can snapmirror, I know concurrent on the above DOT is 100, is it equal to the number of volumes -1 for vol0, thus being 499? 3. A normal Active/Active cluster, what is the maximum distance that is supported between nodes without additional licensing or fc switches etc. Thanks -- View this message in context: http://www.nabble.com/RANDOM-Questions-tp18510440p18510440.html Sent from the Network Appliance - Toasters mailing list archive at Nabble.com.

1 0

FAS200 iSCSI performance
by Amateur-FASadmin 16 Jul '08

16 Jul '08

Dear group What switch equipment should I use between my FAS and two ESX servers ? I'm having slight performance problems on my ERP system. FAS200 with two shelves and iSCSI 1gbit. Regards Jesper Harder ----- -I have a high Google IQ -- View this message in context: http://www.nabble.com/FAS200-iSCSI-performance-tp18480142p18480142.html Sent from the Network Appliance - Toasters mailing list archive at Nabble.com.

3 4

cifs and umask?!?
by Willeke, Jochen 16 Jul '08

16 Jul '08

Hello toasters, we have several volumes with unix-sec style where there is a cifs share on that volume/qtree as well. For this reason we use the usermap.cfg and it works quite well so far. The only question i have is, when i create a new file on a volume/qtree with unix sec-style using the cifs share and a windows user the unix-permission is always 777. Is there something like "umask" which can be set on the filer to get another permission style?? I found a related bug in now but there is no solution :/ http://now.netapp.com/NOW/cgi-bin/bol?Type=Detail&Display=29551 Regards Jochen -- WINCOR NIXDORF International GmbH Sitz der Gesellschaft: Paderborn Registergericht Paderborn HRB 3507 Gesch�ftsf�hrer: Eckard Heidloff (Vorsitzender), Stefan Auerbach, Dr. J�rgen Wunram Vorsitzender des Aufsichtsrats: Karl-Heinz Stiller Steuernummer: 339/5884/0020 - Ust-ID Nr.: DE812927716 - WEEE-Reg.-Nr. DE44477193 Diese E-Mail enth�lt vertrauliche Informationen. Wenn Sie nicht der richtige Adressat sind oder diese E-Mail irrt�mlich erhalten haben, informieren Sie bitte sofort den Absender und vernichten Sie diese E-Mail. Das unerlaubte Kopieren sowie die unbefugte Weitergabe dieser E-Mail ist nicht gestattet. This e-mail may contain confidential information. If you are not the intended recipient (or have received this e-mail in error) please notify the sender immediately and destroy this e-mail. Any unauthorised copying, disclosure or distribution of the material in this e-mail is strictly forbidden.

6 9

Windows Services for Unix NFS Client
by John Legato 15 Jul '08

15 Jul '08

Has anyone had any luck mounting a filer using Window's Services for UNIX NFS Client? I've tried mounting it with mount \\filer\vol\volume and run into a problem with mount not supporting multi directory paths. I get an error message stating "The network path can not be found" with the above mount. I tried accessing it in Windows explorer but it doesn't show up there. I know it can see the filer because I ran into trouble with it using non reserved ports and saw the message in the logs, I've since fixed that issue. Is there a work around for the multi directory path limitation? Thanks John -- Contractor

2 3

Recall: Windows Services for Unix NFS Client
by Langdon, Laughlin T. (Lock) 15 Jul '08

15 Jul '08

Langdon, Laughlin T. (Lock) would like to recall the message, "Windows Services for Unix NFS Client".

1 0

Re: volume deswizzling
by Steve Rieger 15 Jul '08

15 Jul '08

I believe that you can set the wafl priority per volume ------Original Message------ From: Kappe, Michael Sender: owner-toasters(a)mathworks.com To: toasters(a)mathworks.com Sent: Jul 15, 2008 01:19 Subject: volume deswizzling Hello toasters, i have several volume deswizzling processes runing. This is ok, why i copy the volume with snapmirror from one aggr to another. This volume deswizzling processes now running for more than a month. Now the question: When i stop the deswizzling with "wafl scan abort", can i restart them one by one to finish them a bit faster? What is the command? Doing a reboot will restart deswizzling for all volumes. This is not an option ;-) Regards Michael Sent via BlackBerry from T-Mobile

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

toasters