toasters August 2002

toasters@lists.teaparty.net

102 participants
113 discussions

F630 Panic
by Blake Folgner 15 Aug '02

15 Aug '02

Hello All, My F630 has generated these errors below. The Filer is running 6.1.2 and it's in a CIFS environment only. Any Ideas? Wed Aug 14 09:30:04 GMT [raid_xor_server:CRITICAL]: 1 CORR PROC ERR 86 eia:a011720 fs:94 eis:c5000000 isr:100000000 CPU ECC error on SIMM=J100, Address=ffffff000a01172f Wed Aug 14 10:00:00 GMT [kern.uptime.filer:info]: 10:00am up 4 days, 16:33 0 NFS ops, 383717 CIFS ops, 238 HTTP ops Wed Aug 14 11:00:00 GMT [kern.uptime.filer:info]: 11:00am up 4 days, 17:33 0 NFS ops, 385292 CIFS ops, 238 HTTP ops Wed Aug 14 12:00:00 GMT [kern.uptime.filer:info]: 12:00pm up 4 days, 18:33 0 NFS ops, 386935 CIFS ops, 238 HTTP ops Wed Aug 14 12:00:01 GMT [sk.panic:ALERT]: reason="MM fault MMCSR=1, type=0, VA=0x0, PC=0xfffffc00000110d8, RA=0x55360 in process wafl_hipri on release NetApp Release 6.1.2" Wed Aug 14 12:00:01 GMT [sk.assert:ALERT]: file="../driver/scsi/scsi.c", line="1309", expr="NULL" Wed Aug 14 12:00:01 GMT [sk.assert:ALERT]: file="../driver/scsi/scsi.c", line="1309", expr="NULL" Wed Aug 14 12:03:30 GMT [kern.syslog.msg:info]: Ethernet e10a: Link up. Wed Aug 14 12:03:31 GMT [mgr.boot.oldOFW:error]: The current boot firmware version is too old. Please upgrade to version 2.3. Wed Aug 14 12:03:31 GMT [kern.syslog.msg:warning]: Updated boot firmware is available on the Network Appliance NOW site (now.netapp.com). Wed Aug 14 12:03:32 GMT [kern.syslog.msg:info]: Replayed 0 checksum entries Wed Aug 14 12:03:33 GMT [kern.syslog.msg:ALERT]: relog syslog PANIC: MM fault MMCSR=1, type=0, VA=0x0, PC=0xfffffc00000110d8, RA=0x55360 in process wafl_hipri on release NetApp Rel Wed Aug 14 12:03:35 GMT [kern.syslog.msg:ALERT]: Language not set on volume vol0. Using language config "C". Use vol lang to set language. Wed Aug 14 12:03:35 GMT [kern.syslog.msg:notice]: The system was down for 191 seconds Wed Aug 14 12:03:38 GMT [dyn_dev_qual_admin:info]: Firmware is up-to-date on all disk drives Wed Aug 14 12:03:38 GMT [rc:info]: Ethernet e10a: Link up. Wed Aug 14 12:03:38 GMT [rc:info]: relog syslog Wed Aug 14 12:00:01 GMT [wafl_hipri:CRITICAL]: 3 CORR PROC ERR 86 eia:117e0 fs:3 eis:1c5000000 isr:100000000 CPU ECC e Wed Aug 14 12:03:38 GMT [rc:ALERT]: relog syslog PANIC: MM fault MMCSR=1, type=0, VA=0x0, PC=0xfffffc00000110d8, RA=0x55360 in process wafl_hipri on release NetApp Rel Wed Aug 14 12:03:38 GMT [rc:info]: sysconfig: Note: Model F630 has no configuration rules. Wed Aug 14 12:03:38 GMT [mgr.boot.disk_done:info]: NetApp Release 6.1.2 boot complete. Last disk update written at Wed Aug 14 11:59:51 GMT 2002 Wed Aug 14 12:03:38 GMT [mgr.boot.reason_abnormal:ALERT]: System rebooted due to a watchdog reset. Wed Aug 14 12:03:38 GMT [mgr.stack.saved:notice]: Reboot with saved panic information in log file Wed Aug 14 12:03:38 GMT [mgr.stack.string:notice]: Panic string: MM fault MMCSR=1, type=0, VA=0x0, PC=0xfffffc00000110d8, RA=0x55360 in process wafl_hipri on release NetApp Release 6.1.2 Wed Aug 14 12:03:38 GMT [mgr.stack.at:notice]: Panic occurred at: Wed Aug 14 12:00:01 2002 Wed Aug 14 12:03:38 GMT [mgr.stack.proc:notice]: Panic in process: wafl_hipri Wed Aug 14 12:03:38 GMT [mgr.stack.noFrames:notice]: No stack frames available Thanks, Blake

4 3

Interesting Netapp product roadmap
by Look what I found 15 Aug '02

15 Aug '02

Check this out: http://www.zdv.uni-mainz.de/download_files/NetApp_UNI_Mainz.ppt __________________________________________________ Do You Yahoo!? HotJobs - Search Thousands of New Jobs http://www.hotjobs.com

2 1

RE: Interesting Netapp product roadmap
by Peter Bryant 15 Aug '02

15 Aug '02

*** Before acting on this e-mail or opening any attachment you are advised to read the disclaimer at the end of this e-mail *** Only available on Google's cache now... -----Original Message----- From: Look what I found [mailto:look_at_this_mama_mia@yahoo.com] Sent: 14 August 2002 23:27 To: toasters(a)mathworks.com Subject: Interesting Netapp product roadmap Check this out: http://www.zdv.uni-mainz.de/download_files/NetApp_UNI_Mainz.ppt __________________________________________________ Do You Yahoo!? HotJobs - Search Thousands of New Jobs http://www.hotjobs.com ******************************* Disclaimer ***************************** Confidentiality: This e-mail and any attachments are intended for the addressee(s) only and may be confidential. If they have come to you in error you must take no action based on them, nor must you copy or show them to anyone; please reply to this e-mail and highlight the error. Viruses: Although we have taken steps to ensure that this e-mail and attachments are free from any virus, we advise that in keeping with good practice the recipient should ensure they are actually virus free. ********************** http://www.burallplastec.com ********************

1 0

RE: secure filer access
by Ehrhart, Rick 14 Aug '02

14 Aug '02

There is also options httpd.admin.access. You can read man page na_protocolaccess(8) for more details. BTW, options http.access is options httpd.access. The version on ONTAP is 6.2 or later. - Rick - > -----Original Message----- > From: Potakamuri, Sreenivasa [mailto:Sreenivasa.Potakamuri@netapp.com] > Sent: Wednesday, August 14, 2002 10:27 AM > To: 'Moritz Willers'; toasters(a)mathworks.com > Subject: RE: secure filer access > > > > > -----Original Message----- > > From: Moritz Willers [mailto:Moritz.Willers@ubsw.com] > > Sent: Wednesday, August 14, 2002 9:35 AM > > To: toasters(a)mathworks.com > > Subject: secure filer access > > > > > > I'm trying to configure ssh/https admin access from any host > > to a filer, > > but no telnet, no http admin and rsh access from one host only (the > > admin host). > > > > > Use > "options telnet.access", "options rsh.access" and "options > http.access" > commands to control telnet, rsh and http access. > > > > > I can't find how I can control ssh/https access separately. > Is this > > really not possible or am I missing something? > > > > > We don't have any commands to control the ssh/https access. We are > adding those in the next release. > > > Regards, > Sreenivasa Potakamuri > Network Appliance. > > > > > > how do others manage secure filer management via cli and gui? > > > > thanks - Moritz > > > > > > Visit our website at http://www.ubswarburg.com > > > > This message contains confidential information and is intended only > > for the individual named. If you are not the named addressee you > > should not disseminate, distribute or copy this e-mail. Please > > notify the sender immediately by e-mail if you have received this > > e-mail by mistake and delete this e-mail from your system. > > > > E-mail transmission cannot be guaranteed to be secure or error-free > > as information could be intercepted, corrupted, lost, destroyed, > > arrive late or incomplete, or contain viruses. The sender > therefore > > does not accept liability for any errors or omissions in > the contents > > of this message which arise as a result of e-mail transmission. If > > verification is required please request a hard-copy version. This > > message is provided for informational purposes and should not be > > construed as a solicitation or offer to buy or sell any > securities or > > related financial instruments. > > >

1 0

RE: secure filer access
by Potakamuri, Sreenivasa 14 Aug '02

14 Aug '02

> -----Original Message----- > From: Moritz Willers [mailto:Moritz.Willers@ubsw.com] > Sent: Wednesday, August 14, 2002 9:35 AM > To: toasters(a)mathworks.com > Subject: secure filer access > > > I'm trying to configure ssh/https admin access from any host > to a filer, > but no telnet, no http admin and rsh access from one host only (the > admin host). > Use "options telnet.access", "options rsh.access" and "options http.access" commands to control telnet, rsh and http access. > I can't find how I can control ssh/https access separately. Is this > really not possible or am I missing something? > We don't have any commands to control the ssh/https access. We are adding those in the next release. Regards, Sreenivasa Potakamuri Network Appliance. > how do others manage secure filer management via cli and gui? > > thanks - Moritz > > > Visit our website at http://www.ubswarburg.com > > This message contains confidential information and is intended only > for the individual named. If you are not the named addressee you > should not disseminate, distribute or copy this e-mail. Please > notify the sender immediately by e-mail if you have received this > e-mail by mistake and delete this e-mail from your system. > > E-mail transmission cannot be guaranteed to be secure or error-free > as information could be intercepted, corrupted, lost, destroyed, > arrive late or incomplete, or contain viruses. The sender therefore > does not accept liability for any errors or omissions in the contents > of this message which arise as a result of e-mail transmission. If > verification is required please request a hard-copy version. This > message is provided for informational purposes and should not be > construed as a solicitation or offer to buy or sell any securities or > related financial instruments. >

1 0

urgent
by Mr:Davis Masinga 14 Aug '02

14 Aug '02

ATTN: I PRESUME THIS MAIL WILL NOT BE A SURPRISE TO YOU. I AM AN ACCOUNTANT WITH THE MINISTRY OF MINERAL RESOURCES AND ENERGY IN SOUTH AFRICA AND ALSO A MEMBER OF CONTRACTS AWARDING COMMITTEE OF THIS MINISTRY UNDER SOUTH AFRICA GOVERNMENT. MANY YEARS AGO, SOUTH AFRICA GOVERNMENT ASKED THIS COMMITTEE TO AWARDS CONTRACTS TO FOREIGN FIRMS, WHICH I AND 2 OF MY PARTNERS ARE THE LEADER OF THIS COMMITTEE, WITH OUR GOOD POSITION , THIS CONTRACRS WAS OVER INVOICED TO THE TUNE OF US$25,600,000:00 AS A DEAL TO BE BENEFIT BY THE THREE TOP MEMBER OF THIS COMMITTEE. NOW THE CONTRACTS VALUE HAS BEEN PAID OFF TO THE ACTUAL CONTRACTORS THAT EXECUTED THIS JOBS, ALL WE WANT NOW IS A TRUSTED FOREIGN PARTNER LIKE YOU THAT WE SHALL FRONT WITH HIS BANKING ACCOUNT NUMBER TO CLAIM THE OVER INFLATED SUM. UPON OUR AGREEMEENT TO CARRY ON THIS TRANSACTION WITH YOU, THE SAID FUND WILL BE SHARE AS FOLLOWS. 75% WILL BE FOR US IN SOUTH AFRICA. 20% FOR USING YOUR ACCOUNT AND OTHER CONTRIBUTION THAT MIGHT REQIURED FROM YOU. 5% IS SET ASIDE FOR THE UP FRONT EXPENCES THAT WILL BE ENCOUNTER BY BOTH PARTY TO GET ALL NECESSARY DOCUMENTS AND FORMARLITIES THAT WILL JUSTIFY YOU AS THE RIGHTFUL OWNER OF THIS FUND. IF YOU ARE INTERESTED IN THIS TRANSACTION, KINDLY REPLY THIS MASSEGE WITH ALL YOUR PHONE AND FAX NUMBERS, OR MAIL ME THROUGH(d_masinga(a)totalise.co.uk) TO ENABLE US FURNISH YOU WITH DETAILS AND PROCEDURES OF THIS TRANSACTION. YOURS FAITHFULLY. Davis Masinga

2 1

Do you make conference calls?
by I-Corporate News 13 Aug '02

13 Aug '02

1 0

Moving a viewstore from Windows NT onto Netapp f740 filer
by Kumar, Rahul 13 Aug '02

13 Aug '02

Dear Fellows, Can somebody guide me with how to move an existing viewstore which is on windows nt server onto a filer. I am aware of following commands cifs access /vol/vol0/viewstgnt -g develop "full control" cifs access /vol/vol0/viewstgnt clearcase_albd "full control" The server from which we are supposingly to move viewstore is a NT Build machine. Regards Rahul

1 0

NFS Delay
by Tim Longo 12 Aug '02

12 Aug '02

I've noticed that when I make a change on an nfs mounted file system on my Netapp from one machine, it sometimes takes anywhere from a few seconds to a minute for other machines that access the same nfs mounted file system to see the change I made from the first machine. The clients are unix and linux machines. Example: On my admin host (unix machine), I change permissions on an exported directory. A unix client that automounts this directory takes 20 to 30 seconds before I see the directory permissions change. Anyone else experience something like this? What sort of things should I be checking to reduce or eliminate this delay? Thanks.

5 4

cp command on NetApp?
by Edward Hibbert 12 Aug '02

12 Aug '02

I want to copy large amounts of data around, and I'm reluctant to pull the data down from the filer and push it back again. I know there's a mv command on the NetApp - is there any way of doing a cp? And if so, does it come with a particular ONTAP version? Regards, Edward Hibbert Internet Applications Group Data Connection Ltd Tel: +44 131 662 1212 Fax: +44 131 662 1345 Email: eh(a)dataconnection.com Web: http://www.dataconnection.com

3 2

← Newer
1
...
4
5
6
7
8
9
10
11
12
Older →

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

toasters August 2002