Hi
I have just renumbered our FAS940 and I cant see a way to renumber the autosupport card. Does anyone know how to do this ?
netapp> sysconfig -av 1 slot 1: Remote Management Controller Serial Number: DE441500188 Firmware Version: RMC_NA_1.3 POST Status: OK Mgmt MAC Address: 00:30:d3:09:f0:34 (auto) LAN dhcp n ip 192.168.101.4 netmask 255.255.255.0 gw 192.168.101.62
I need to get a different IP and gateway into this our dhcp servers are correct.
Cheers Vin
Hey,
We are having an issue with DFM reporting "qtree capacity" incorrectly, no real errors can be found in the logs, and it is quite a mystery.
It worked perfectly until last week, and now it is only reporting that same old figures over and over again, and never updating the numbers.
Does any of you have experiences regarding these kind of issues and how did you solve it?
(we are running dfm 3.2)
Thanks and Regards, Hannu
Visit our website at http://www.ubs.com
This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.
E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message which arise as a result of e-mail transmission. If verification is required please request a hard-copy version. This message is provided for informational purposes and should not be construed as a solicitation or offer to buy or sell any securities or related financial instruments.
Check if you have turned off quotas for the volume where these qtrees are located. DFM expects quotas to be turned on, and quotas to be set for the qtrees it monitors, even if it's just a "counting rule" - one that has a "-" instead of a hard/soft/threshold limit.
Eyal.
On 6/6/06, Hannu.Kettinen@ubs.com Hannu.Kettinen@ubs.com wrote:
Hey,
We are having an issue with DFM reporting "qtree capacity" incorrectly, no real errors can be found in the logs, and it is quite a mystery.
It worked perfectly until last week, and now it is only reporting that same old figures over and over again, and never updating the numbers.
Does any of you have experiences regarding these kind of issues and how did you solve it?
(we are running dfm 3.2)
Thanks and Regards, Hannu
Visit our website at http://www.ubs.com
This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.
E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message which arise as a result of e-mail transmission. If verification is required please request a hard-copy version. This message is provided for informational purposes and should not be construed as a solicitation or offer to buy or sell any securities or related financial instruments.
Try "rmc setup".
Eyal.
On 6/6/06, Vin Everett vin.everett@cimr.cam.ac.uk wrote:
Hi
I have just renumbered our FAS940 and I cant see a way to renumber the autosupport card. Does anyone know how to do this ?
netapp> sysconfig -av 1 slot 1: Remote Management Controller Serial Number: DE441500188 Firmware Version: RMC_NA_1.3 POST Status: OK Mgmt MAC Address: 00:30:d3:09:f0:34 (auto) LAN dhcp n ip 192.168.101.4 netmask 255.255.255.0 gw 192.168.101.62
I need to get a different IP and gateway into this our dhcp servers are correct.
Cheers Vin
Vin.Everett@cimr.cam.ac.uk JDRF/WT Diabetes and Inflammation Laboratory (DIL) Wellcome Trust/MRC Building Addenbrooke's Hospital Hills Road Cambridge Cambridgeshire CB2 2XY Tel +44 1223 763212 Fax +44 1223 762102 Mob +44 7990 966266
Eyal Traitel wrote:
Try "rmc setup".
Eyal.
Thanks Eyal,
been able to set a new number now waiting for sysconfig to show it.
Able to send a test autosupport from my old number so problem may be a bit deeper but one thing at a time ;-)
Cheers Vin
-
Eyal Traitel -
Hannu.Kettinen＠ubs.com -
Vin Everett