toasters

toasters@lists.teaparty.net

1 participants
13523 discussions

Deduplication and space usage - best practices
by Ray Van Dolson 28 Jul '10

28 Jul '10

We use deduplication on our N3600 (FAS2050C) with ESX (vSphere these days) via NFS. I'm curious how those of you out there with a similar setup manage your disk space and identify "critical" threshholds. We also do thin provisioning so we're thinking about a worst-case scenario where we have to restore from backups and end up with thick provisioned and non deduped VMDK files. We don't want to be too conservative though -- may as well not be using dedupe at all... :) Interested in how others on the list deal with this. Thanks, Ray

2 1

10gb Network Bandwidth concern
by ifstat 21 Jul '10

21 Jul '10

We have installed dual port 10Gbe (x1008a-r6) in our FAS3170A, configured them as a vif using lacp, with load balancing as mac. What we are noticing is that we are only get 1.4Gbits bandwidth per port. Even though we should realy be achiving at least 20Gbits. The filers connect to a 6509 CISCO switch, with each interface connecting to a different module for redundancy. The two interfaces from the filer define a port channel on the switch so that they reflect the vif on each filer. The tool we use to check on the throughput is called Solarwinds and Orion. This tool shows that: a. For netapp1, each interface is shown to work at 1.4101Gbits. The vif is shown to work at 2.8201Gbits. b. For netapp2, each interface is shown to work at 10Gbits. The vif is shown to work at 20Gbits, but we don't get more that 2.8201 Gbits Is this normal or what are we misising? We have a case open (2001542643) is anyone for NetApp has access. Thanks -- View this message in context: http://old.nabble.com/10gb-Network-Bandwidth-concern-tp29222397p29222397.ht… Sent from the Network Appliance - Toasters mailing list archive at Nabble.com.

5 4

Slot labeling for a 3070?
by Page, Jeremy 20 Jul '10

20 Jul '10

I'm getting a set of PAM II cards for my 3070 and have started doing some of the installation research. The system configuration guide recommends they be installed in specific slots but I can't tell what they mean. Is there a doc that has the slots diagrammed in it? Please be advised that this email may contain confidential information. If you are not the intended recipient, please notify us by email by replying to the sender and delete this message. The sender disclaims that the content of this email constitutes an offer to enter into, or the acceptance of, any agreement; provided that the foregoing does not invalidate the binding effect of any digital or other electronic reproduction of a manual signature that is included in any attachment.

2 1

nitro security and cifs auditing
by Halton, Robert 15 Jul '10

15 Jul '10

Has anyone been using Nitro security for auditing CIFS? Any caveats? Thanks This message is intended only for the person(s) to which it is addressed and may contain privileged, confidential and/or insider information. If you have received this communication in error, please notify us immediately by replying to the message and deleting it from your computer. Any disclosure, copying, distribution, or the taking of any action concerning the contents of this message and any attachment(s) by anyone other than the named recipient(s) is strictly prohibited.

1 0

Boot from SAN
by David McWilliams 12 Jul '10

12 Jul '10

Does anyone know how to configure boot from SAN when we multiple paths available to us? Obviously we will not have true mutlipathing available to us at the BIOS level. Is configuration of the boot order an acceptable solution or does anyone else know of any cleverness out there. Sláinte, David "Build a man a fire he'll be warm for a day, set a man on fire and he'll be warm for the rest of his life" - Terry Pratchett Checkout my photos - http://www.panoramio.com/user/1113507

1 0

Re: Physical displacement of disk shelves -- hot ?
by Simon Vallet 02 Jul '10

02 Jul '10

On Fri, 2 Jul 2010 16:39:58 +0300 Marek.Stopka(a)tieto.com wrote: > Hey guys, what if you would keep it in English or took it outside this > public mail list? Sorry. In English, the short answer was that this operation is not possible. On Fri, 2 Jul 2010 12:59:49 +0300 "Mike" <hockey(a)spidernet.net> wrote: > There is a way to take an aggregate offline without maintenance mode, but > you need to speak to support. I have never used it and I don't know if they > will allow you to use it either. It's either in advanced mode or diagnostics > mode. Plead your case maybe they will provide the solution I will try that -- thanks! Simon

1 0

Physical displacement of disk shelves -- hot ?
by Simon Vallet 02 Jul '10

02 Jul '10

Hi, I'm currently trying to physically move two aggregates from one filer (3020) to another one (2050), and I'd like to do that without service interruption. AFAICT, I'm first supposed to boot one head under maintenance mode to take the aggregate offline, but when I do that (on the taked-over head), I get a quite scary message relative to possible data corruption. So the question is : is it at all possible to take an aggregate (containing FlexVols) offline and move disk shelves in takeover mode ? Cheers, Simon

3 3

upgrading fas3050c to fas3170a
by ifstat 01 Jul '10

01 Jul '10

I'm upgrading FAS3050C to FAS3170A I know of the following tasks: 1- same version ONTAP on old and new controllers 2- disk reassign ownership form old_sysid to new_sysid 3- mailbox destroy local 4- mailbox destroy partner 5- lun serial numbers to be change to what they were before the upgrade 6- software install ONTAP for FAS3170 after upgrade 7- license add 8- edit /etc/rc file for networking ports to correspond to new ports e0c to e4a example. Is there something that i'm missing or any other gotcha's that i can avoid. -- View this message in context: http://old.nabble.com/upgrading-fas3050c-to-fas3170a-tp29043587p29043587.ht… Sent from the Network Appliance - Toasters mailing list archive at Nabble.com.

2 1

SL SMB misery
by Carl Howell 25 Jun '10

25 Jun '10

Like many of you, we have been having lots of weird issues with Snow Leopard and SMB. We've upgraded to 7.3.3, but that hasn't helped. A lot of the symptoms we are experiencing are mentioned here: http://discussions.apple.com/message.jspa?messageID=11041594 For those of you that are having these problems, what are you doing to try to solve them? Thanks, Carl Howell Systems Engineer Information Technology Services

1 0

I: Snapdrive 6.2 and Net.TCP Port Sharing Service Issue
by Milazzo Giacomo 25 Jun '10

25 Jun '10

I've not surrended myself to Microsoft nightmares!!! :) With the help of Process Monitor I was able to find where that damned service fails (if not administrator). I don't know the reasons but installing and or patching .net 3.5sp1 (and of course the related patches to the 3.0 and 2.0 too) on a Windows 2003 italian (or other than eng) does not fix the permissions needed from this service on file system. There's a system folder where the LOCALSERVICE account need to be explicited with Generic Read permission. To do this you need CACLS. The syntax is cacls c:\windows\assembly /E /T /G "NT AUTHORITY\LOCALSERVICE":R From this moment ahead the Net.Tcp services stays loaded and of course Snapdrive too... Bye, Da: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com] Per conto di Milazzo Giacomo Inviato: venerdì 25 giugno 2010 13:11 A: toasters(a)mathworks.com Oggetto: I: Snapdrive 6.2 and Net.TCP Port Sharing Service Issue News on this issue. It's certain that is a permission issue. There are a lot of people on several forums reporting this kind of problems on Net.Tcp Service. If I manually add the LOCAL SERVICE account to the local Administrators group the service starts fine and remains started and Snapdrive work. Of course, I cannot maintain this builtin account in the Administrators ;-) I've also tried to manually set permissions on the folders but with no success... Da: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com] Per conto di Milazzo Giacomo Inviato: venerdì 25 giugno 2010 11:41 A: toasters(a)mathworks.com Oggetto: Snapdrive 6.2 and Net.TCP Port Sharing Service Issue Hi everybody, Regarding this article https://now.netapp.com/Knowledgebase/solutionarea.asp?id=kb44514... The issues started since the installation phase of Snapdrive 6.2 (the SD used is 6.2D3) when I discovered that this Net.Tcp service did not started using localservice (???). Erroneusly I put "local system" as account and this started letting me install SD. Then, when I call SD to create some LUN the other issues begin. I've tried every possible fix and workaround but I'm still getting the Issue 1 or Issue 2 and Snapdrive does not connect to the LUN Provisioning service... I suspect that there's some hidden issue caused to the Windows 2003 language: in this case is Italian. In fact the NT AUTHORITY\LocalService wanted to start the Net.Tcp service used by Snapdrive has to be NT AUTHORITY\SERVIZIO LOCALE...anyway if I manually choose "SERVIZIO LOCALE" as user it is automatically converted in NT AUTHORITY\LocalService. Regards, Giacomo,

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

toasters