Spot on - that's done the trick. Had '0a.01.0' with a foreign owner ID hiding in the list somewhere. I can only assume as part of a reboot/rebuild/pre-ship-test or something.
Reassigned it to 'unowned' and all good. (well, a 'foreign aggr0(1)' showed up).
On 11 June 2015 at 13:15, tmac tmacmd@gmail.com wrote:
SO, look at the output of disk show -a The -n shows all non-owned disks.
Look for disks not owned by either of your two nodes now. If there are any disks owned by another party....ugh, little bit of work involved.
If not, do your best to verify which disks on which shelves are owned and where.
Sometimes it is helpful to run through the disks one by one, if possible, use a sorting routine to put the disks in order to make looking at the list easier.
Let us know!
--tmac
*Tim McCarthy* *Principal Consultant*
On Thu, Jun 11, 2015 at 8:12 AM, tmac tmacmd@gmail.com wrote:
any chance you can copy to a flash drive or the like? or is it more secure than that ;)
--tmac
*Tim McCarthy* *Principal Consultant*
On Thu, Jun 11, 2015 at 8:11 AM, Edward Rolison ed.rolison@gmail.com wrote:
Sadly I can't - this is a system on an isolated network. I can re-type parts of it, but that's probably not as useful. :/
On 11 June 2015 at 12:42, tmac tmacmd@gmail.com wrote:
Hey Edward, just for kicks, how about posting the "disk show -a" for us.
Thanks
--tmac
*Tim McCarthy* *Principal Consultant*
On Thu, Jun 11, 2015 at 7:26 AM, Edward Rolison ed.rolison@gmail.com wrote:
New disks are all listed in 'disk show -n'. I think that means they're not assigned. (And a disk I've deliberately unassigned is also not being reassigned).
On 11 June 2015 at 12:12, Borzenkov, Andrei < andrei.borzenkov@ts.fujitsu.com> wrote:
Are you sure new disks are unowned? It is not uncommon to get repurposed hardware.
*From:* Edward Rolison [mailto:ed.rolison@gmail.com] *Sent:* Thursday, June 11, 2015 2:09 PM *To:* Borzenkov, Andrei *Cc:* toasters@teaparty.net *Subject:* Re: Disk auto assign
Sorry, should have said - also did this with the spares. I can see no drives on 'head1' sysconfig -r that are 'wrong' and likewise on 'head2'.
Checked this with grepping 'partner' and ensuring they're all the right pair of controllers. (On both sides)
On 11 June 2015 at 11:56, Borzenkov, Andrei < andrei.borzenkov@ts.fujitsu.com> wrote:
If you just performed “replace” without un-/re-assigning drives that became spare, this is expected. Spares still belong to controller and will block auto assignment.
*From:* toasters-bounces@teaparty.net [mailto: toasters-bounces@teaparty.net] *On Behalf Of *Edward Rolison *Sent:* Thursday, June 11, 2015 1:09 PM *To:* toasters@teaparty.net *Subject:* Disk auto assign
I've just added some new shelves to a (7-mode) filer pair, bring them up to two stacks of 10 shelves.
I'm trying to get 'autoassign' working, and it isn't.
I have:
- swapped drives such that each 'head' has only disks from one
'stack'.
Head 1 has 0a/5b
Head 2 has 5a/5d
I've had to manually trigger a small number of 'replace' operations. And then switched on autoassign in the options.
I _think_ that should be it, but ... there's something I'm missing, because autoassign isn't working.
Does anyone have suggestions for why this might be, or what else I could check? (I'm wondering if there's a misassigned but 'failed' drive that otherwise isn't showing up?)
Toasters mailing list Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters
-
Edward Rolison