toasters

toasters@lists.teaparty.net

2 participants
13529 discussions

Question on iSCSI and Network Interfaces
by Glenn Dekhayser 06 Apr '06

06 Apr '06

Can I turn off iSCSI for a particular network interface? Suppose I have a Quad 10/100/1000 card (e5a-d), and the built-in 10/100 (e0). Obviously I wouldn't want to serve iSCSI on e0- I want to serve CIFS on that, but not allow iSCSI connections on that interface. Anyone? Glenn (the other one)

2 1

Cher Ami
by mrs villaran nenita 06 Apr '06

06 Apr '06

Cher Ami , j'ai bien reçu votre message et je vous avoue que cela me ferait plaisir de lier plus qu'une amitié avec vous. Longtemps, j'ai réfléchi et enfin je me décide. Mais avant, je tiens a me présenter a vous. Je me rejoui que vous avyez enfin pri contact avec moi. Mon nom est madame Villaran Nenita,je suis une citoyenne philippienne a part entiere et la veuve du défunt ministre des finances philippien qui est mort le 15 mai 2002. Mon mari est tombé gravement malade est a donc été conduit en Europe pour des soins intensifs, mais plus tard il est décédé des suites de sa maladie et a été enterré. J’ai donc hérité de mon défunt mari la somme de 12.000.000 de dollars américains (douze millions de dollars américains). Cet argent, je l’ai caché dans une mallette métallique et déposé au sein d’une compagnie de finance et de sécurité ici en Philippine.Cependant, ayant insisté aupres de la compagnie de finance et de sécurité pour que ma mallette soit gardée avec un maximum de sécurité de tel sorte que personne ni meme une organisation gouvernementale philippienne ne puisse prendre connaissance de son existence, jusqu’a ce que je sois prete a la retirer, alors la dite compagnie pour répondre a mon exigence maximum de sécurité a utilisé des moyens diplomatiques pour envoyer ma mallette hors des philippines et précisément a la maison mere de leur compagnie en côte d’ivoire en Afrique de l’ouest ou ma mallette se trouve donc discretement gardée dans le coffre fort de la compagnie. Ce dépôt a été fait et codé dans le cadre d’un arrangement secret selon lequel ma mallette contient uniquement des biens de famille.Cela signifie donc que la compagnie elle meme ne connaît pas le contenu exact de la mallette qui pour plus de sécurité a été envoyée en côte d’ivoire sous une assurance diplomatique et déclarée comme contenant des biens de famille .Aussi,la raison principale pour laquelle je vous envoie ce courrier est qu’aujourd’hui, n’ayant plus confiance en mon entourage ici en philippine et la côte d’ivoire étant un pays en proie a la guerre, je me retrouve dans une impasse et je voudrais que vous m’aidiez discretement a emmener ma mallette d’argent a une adresse beaucoup plus discrete et stable dans votre pays ou je pourrai commencer a investir. Si vous voulez sincerement m’aider, nous discuterons au préalable du pourcentage que je vous donnerai sur la somme totale se trouvant dans la mallette. En fait, depuis la mort de mon mari, ses freres m’ont chassée de la maison familiale et ont essayé a plusieurs reprises de porté atteinte a ma vie pensant qu’a ma mort tous les documents légaux des biens que possédaient mon mari leur reviendraient de plein droit.Grâce a la notoriété et aux relatons influentes que possedent les freres de mon mari, ils ont réussi a m’arracher toutes les propriétés de mon défunt mari ainsi que tous ses biens matériels. Mais ils ne se sont pas arretés la et m’ont obligée a leur révéler tous les comptes bancaires de mon défunt mari en menaçant a nouveau ma vie.Je leur est donc donner ces informations et ils ont confisqués tous les comptes bancaires de feu mon mari.Je leur est tout révéler sauf l’existence de ce dépôt que j’ai fait au sein de la compagnie de finance et de sécurité a Abidjan en côte d’ivoire car ceci représente tout mon secret espoir caché. La famille de mon défunt mari n’est donc pas informé de l’existence de ce dépôt que j’ai fait au sein de la compagnie de sécurité et elle ne le saura jamais. Cependant, j’ai toujours peur des freres de mon mari car ils continuent a m’espionner et vont jusqu’a écouter mes conversations. C’est pourquoi j’ai décidé de chercher quelqu’un de confiance a l’extérieur des philippines qui m’aidera a retirer la mallette de la compagnie de finance et de sécurité et placer discretement l’argent dans son compte a l’étranger pour un investissement futur. Je vous demande de considérer ma situation qui est celle d’une veuve et de venir a mon aide car aujourd’hui a part cette mallette, je n’ai plus d’argent et ma situation financiere est plus que difficile(ma situation financiere est a zéro). Et ma demande d’aide est d’autant plus urgente que je paye 100 dollars par jour a cette compagnie de sécurité comme frais de stockage et de sécurité de ma mallette. Si vous désirez m’aider, je vous ferez parvenir dans mon prochain email, les coordonnées de la compagnie de securité afin que vous les contactiez pour l’envoie immédiat de cette mallette vers vous pour la securiser. Je vous remercie infiniment pour votre coopération et j’attends de vos nouvelles pour la conclusion de cette affaire. Bien a vous MADAME VILLARAN NENITA NB:Que cette année soit pour nous source d'espoir

1 0

RE: Question on iSCSI and Network Interfaces
by Hirschorn, Steven 06 Apr '06

06 Apr '06

http://now.netapp.com/NOW/knowledge/docs/ontap/rel704/html/ontap/bsagiscs/c… Disabling iSCSI on a storage system interface <http://now.netapp.com/NOW/knowledge/docs/ontap/rel704/html/ontap/bsagiscs/c…> Top To disable the iSCSI service on an interface, complete the following step. Step Action 1 Enter the following command: iswt interface disable [-f] {-a | interface ... } -f forces the termination of any outstanding iSCSI sessions without prompting you for confirmation. If you do not use this option, the iswt command displays a message notifying you that active sessions are in progress on the interface and requests confirmation before terminating these sessions and disabling the interface. -a specifies all interfaces. interface is a specific Ethernet interface. -----Original Message----- From: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com]On Behalf Of Glenn Dekhayser Sent: 06 April 2006 14:29 To: toasters(a)mathworks.com Subject: Question on iSCSI and Network Interfaces Can I turn off iSCSI for a particular network interface? Suppose I have a Quad 10/100/1000 card (e5a-d), and the built-in 10/100 (e0). Obviously I wouldn't want to serve iSCSI on e0- I want to serve CIFS on that, but not allow iSCSI connections on that interface. Anyone? Glenn (the other one) ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email ______________________________________________________________________ ------------------------------------------------------------------------------------ Watch Public Information Films including "Charley Says" http://www.nationalarchives.gov.uk/films/1964to1979/filmindex2.htm ----------------------------------------------------------------------------------- National Archives Disclaimer This email message (and attachments) may contain information that is confidential to The National Archives. If you are not the intended recipient you cannot use, distribute or copy the message or attachments. In such a case, please notify the sender by return email immediately and erase all copies of the message and attachments. Opinions, conclusions and other information in this message and attachments that do not relate to the official business of The National Archives are neither given nor endorsed by it. ------------------------------------------------------------------------------------

1 0

RE: Question on iSCSI and Network Interfaces
by Carl Howell 06 Apr '06

06 Apr '06

Iswt interface disable e0 ________________________________ From: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com] On Behalf Of Glenn Dekhayser Sent: Thursday, April 06, 2006 8:29 AM To: toasters(a)mathworks.com Subject: Question on iSCSI and Network Interfaces Can I turn off iSCSI for a particular network interface? Suppose I have a Quad 10/100/1000 card (e5a-d), and the built-in 10/100 (e0). Obviously I wouldn't want to serve iSCSI on e0- I want to serve CIFS on that, but not allow iSCSI connections on that interface. Anyone? Glenn (the other one)

1 0

RE: Question on iSCSI and Network Interfaces
by Jon Kroff 06 Apr '06

06 Apr '06

You are able to disable iSCSI connections to a particular network interface. "iswt interface show" will show you the current interface status "iswt interface disable interface" would disable the given interface (example: iswt interface disable e0) It took me a while to find these commands, so I am glad I can same someone else the trouble of searching. Hope this helps. ________________________________ From: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com] On Behalf Of Glenn Dekhayser Sent: Thursday, April 06, 2006 7:29 AM To: toasters(a)mathworks.com Subject: Question on iSCSI and Network Interfaces Can I turn off iSCSI for a particular network interface? Suppose I have a Quad 10/100/1000 card (e5a-d), and the built-in 10/100 (e0). Obviously I wouldn't want to serve iSCSI on e0- I want to serve CIFS on that, but not allow iSCSI connections on that interface. Anyone? Glenn (the other one)

1 0

RE: OnTap 6.x, mixed shelves, and spares.
by McLoughlin, John 06 Apr '06

06 Apr '06

Yes, Nate. It will prefer the 36GB drive over the 144GB drive. OnTap has a sense for how big a drive is and selects the closest sized drive for spares. ;) Thanks, John. -----Original Message----- From: Nathan Patwardhan [mailto:nvp@akamai.com] Sent: Wednesday, April 05, 2006 10:50 PM To: Tim McCarthy Cc: toasters(a)mathworks.com Subject: Re: OnTap 6.x, mixed shelves, and spares. On Wed, Apr 05, 2006 at 09:56:32PM -0400, Tim McCarthy wrote: : ontap will only ever use a disk that is at lest as big as the failed : disk. In other words, ontap may: : grab a 144 to replace a 36 Alrighty. But if I load the FC9s with an ample number of 36g drives, would OnTap more likely than not pull from the FC9 before the DS14? : Also, since you have FC9 shelves, you may have 36GB Zoned checksum : disks. If they are, then you can replace them with either zoned or block : checksum disks. However, at the 36GB capacity, zoned disks are 34.5G I think ours show as 34g. Thanks for your response! -- Nathan Patwardhan, UNIX System[s] Administrator, Sr. Akamai Technologies, 839B/8CC x 83035 npatward(a)akamai.com AIM: notoriousnvp71

2 1

RE: Files on CIFS share have timestamp off by one hour after daylight saving
by Willeke, Jochen 06 Apr '06

06 Apr '06

Hi, the client and the filer both are hosted in CET timezone which is GMT +1 (Europe\Berlin in filerview) I can view the files with different clients but the result is the same. I had a look at the filer and the time is correct. But i found out something interesting.... The problem really is how windows looks at the files. If i set the date on my computer to November or back to Januar when we do not have the daylight saving the "timestamp" windows shows me is correct again. I will have a look at MS Knowledgebase, perhaps i will find a fix for this problem. Thanks a lot for pointing me in the right direction... BTW: Can anybody of you see the same effect? Jochen -----Original Message----- From: Glenn Walker [mailto:ggwalker@mindspring.com] Sent: Thursday, April 06, 2006 2:11 PM To: Willeke, Jochen; toasters(a)mathworks.com Subject: RE: Files on CIFS share have timestamp off by one hour after daylight saving What are you viewing the timestamps with? What timezone is that machine in? What timezone is the filer in? My guess: when the client wrote the files, it did so with the filer's timestamp (based on the clock on the filer). When the client reads the timestamp back, it adjusts based on the difference - ie, if the file timestamp is stored in GMT (non-daylight savings time) and the client suddenly adjusts its clock, then it has to calculate for an extra hour. So the only way I could see this happening is if the clock rolled forward on the client (or adjusted on the filer too) but the savings time wasn't included in the calculation. Check the clocks... start there. Glenn -----Original Message----- From: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com] On Behalf Of Willeke, Jochen Sent: Thursday, April 06, 2006 6:57 AM To: toasters(a)mathworks.com Subject: Files on CIFS share have timestamp off by one hour after daylight saving Hi everybody, i have a case of one user who stored some files from his Windows2000 client onto a CIFS share on a fas3050 with Ontap 6.5.4. When he first copied the files onto the share the creation time was 10:00 o'clock. This was the Friday before we had the daylight saving change. On next monday the creation time was not 10:00 but 11:00. I have no clue how this could happen. Anybody got an idea? I would be glad even if i get some information about how timestamps are created so i can make a research myself. Thanks a lot for any suggestions in advance Jochen

1 0

RE: Files on CIFS share have timestamp off by one hour after daylight saving
by Glenn Walker 06 Apr '06

06 Apr '06

What are you viewing the timestamps with? What timezone is that machine in? What timezone is the filer in? My guess: when the client wrote the files, it did so with the filer's timestamp (based on the clock on the filer). When the client reads the timestamp back, it adjusts based on the difference - ie, if the file timestamp is stored in GMT (non-daylight savings time) and the client suddenly adjusts its clock, then it has to calculate for an extra hour. So the only way I could see this happening is if the clock rolled forward on the client (or adjusted on the filer too) but the savings time wasn't included in the calculation. Check the clocks... start there. Glenn -----Original Message----- From: owner-toasters(a)mathworks.com [mailto:owner-toasters@mathworks.com] On Behalf Of Willeke, Jochen Sent: Thursday, April 06, 2006 6:57 AM To: toasters(a)mathworks.com Subject: Files on CIFS share have timestamp off by one hour after daylight saving Hi everybody, i have a case of one user who stored some files from his Windows2000 client onto a CIFS share on a fas3050 with Ontap 6.5.4. When he first copied the files onto the share the creation time was 10:00 o'clock. This was the Friday before we had the daylight saving change. On next monday the creation time was not 10:00 but 11:00. I have no clue how this could happen. Anybody got an idea? I would be glad even if i get some information about how timestamps are created so i can make a research myself. Thanks a lot for any suggestions in advance Jochen

1 0

Re: FAS270 FAIL TO INSTALL
by Tim McCarthy 06 Apr '06

06 Apr '06

I have seen cases where the serial console port was slightly moved...enough to look like the boot process stopped, or that the serial port stopped working and it looks like the system stopped. Gabriel Ajidele wrote: > Friends, > > Thanks a lot. > > I got to the site to try the hints given, but to my surprise the machine > booted normally without doing anything. Surprising. I then ran boot diag > and ran all tests, PASSED. > > The machine has been installed and working OK now. > > Regards, > Gabriel. > > >> From: Tim McCarthy <tmacmd(a)gmail.com> >> To: Gabriel Ajidele <gajidele(a)hotmail.com> >> CC: toasters(a)mathworks.com >> Subject: Re: FAS270 FAIL TO INSTALL >> Date: Tue, 04 Apr 2006 20:34:22 -0400 >> >> read the info on how to netboot. Get the image, turn on a tftp server >> and try booting via tftp...or whatever they suppotr on the FAS200 >> series these days. >> >> --tmac >> >> Gabriel Ajidele wrote: >>> Friends, >>> >>> Got a new FAS270, 14 x 144GB Disks. At power up, it displays the >>> following message on the console and nothing else happens, not even >>> after about five minutes: >>> >>> CFE version 1.2.0 based on Broadcom CFE: 1.0.35 >>> Copyright (C) 2000,2001,2002,2003 Broadcom Corporation. >>> Portions Copyright (C) 2002,2003 Network Appliance Corporation. >>> >>> HyperTransport: 400 MHz >>> CPU type 0x1040102: 650MHz >>> Total memory: 0x40000000 bytes (1024MB) >>> >>> >>> Starting AUTOBOOT press any key to abort... >>> Loading: 0xffffffff80001000/8823228 Entry at 0xffffffff80001000 >>> Starting program at 0xffffffff80001000 >>> Press CTRL-C for special boot menu >>> ............................................................................... >>> >>> >>> ............................................................................... >>> >>> >>> ............................................................................... >>> >>> >>> ............................................................................... >>> >>> >>> ................................................................ >>> >>> >>> There are no error LEDs on, the Power LED is on and is green. The >>> Status LEDs are off. The terminator on is set to ON. The Disk LEDs >>> are on and green. The Shelf ID is 1 but this is not displayed in the >>> front. I tried to boot the backup, the same problem occured. >>> >>> Information to solving this problem will be appreciated. >>> >>> Regards, >>> Gabriel. >>> >>> _________________________________________________________________ >>> Express yourself instantly with MSN Messenger! Download today it's >>> FREE! http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/ >>> >>> >>> > > _________________________________________________________________ > Express yourself instantly with MSN Messenger! Download today it's FREE! > http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/ > > >

1 0

Files on CIFS share have timestamp off by one hour after daylight saving
by Willeke, Jochen 06 Apr '06

06 Apr '06

Hi everybody, i have a case of one user who stored some files from his Windows2000 client onto a CIFS share on a fas3050 with Ontap 6.5.4. When he first copied the files onto the share the creation time was 10:00 o'clock. This was the Friday before we had the daylight saving change. On next monday the creation time was not 10:00 but 11:00. I have no clue how this could happen. Anybody got an idea? I would be glad even if i get some information about how timestamps are created so i can make a research myself. Thanks a lot for any suggestions in advance Jochen

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

toasters