Maybe that has changed with OnTap 9.1? I’m running 9.1RC2 here on this filer and not because I’m brave, but because it got shipped with it ☺
Alexander Griesser Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.commailto:AGriesser@anexia-it.com Web: http://www.anexia-it.comhttp://www.anexia-it.com/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: jordan slingerland [mailto:jordan.slingerland@gmail.com] Gesendet: Mittwoch, 14. Dezember 2016 23:27 An: Alexander Griesser AGriesser@anexia-it.com Cc: toasters@teaparty.net; Brad Thompson brad.thompson877@gmail.com Betreff: Re: AW: System attention LED
Hmm, expected it to look like this listing charge voltage. Current and hours it can hold
https://kb.netapp.com/support/s/article/how-to-check-the-nvram-battery-statu...
On Dec 14, 2016 5:16 PM, "Alexander Griesser" <AGriesser@anexia-it.commailto:AGriesser@anexia-it.com> wrote: Looks good to me:
netapp01> environment status chassis list-sensors Sensor Name State Current Critical Warning Warning Critical Reading Low Low High High ------------------------------------------------------------------------------------------------- PSU2 FRU GOOD PSU1 FRU GOOD SP Status IPMI_HB_OK mSATA Status OK mSATA Pres PRESENT
Best,
Alexander Griesser Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.commailto:AGriesser@anexia-it.com Web: http://www.anexia-it.comhttp://www.anexia-it.com/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: Brad Thompson [mailto:brad.thompson877@gmail.commailto:brad.thompson877@gmail.com] Gesendet: Mittwoch, 14. Dezember 2016 23:09 An: Alexander Griesser <AGriesser@anexia-it.commailto:AGriesser@anexia-it.com> Cc: toasters@teaparty.netmailto:toasters@teaparty.net Betreff: Re: System attention LED
The battery might be charging. check: environment status chassis list-sensors
On Wed, Dec 14, 2016 at 4:49 PM, Alexander Griesser <AGriesser@anexia-it.commailto:AGriesser@anexia-it.com> wrote: Hi Brad,
netapp01> storage show fault No faults found in storage subsystem netapp02> storage show fault No faults found in storage subsystem
No luck with `system fru led show` on the SP of the 2650:
SP netapp01*> system fru led show system fru show - display fru id inventory data system fru list - list fru id system fru log show - display fru log system fru log clear - clear fru log
But this one seems to work (I’ve highlighted the ones where the LED seems to be in the „on“ state):
SP netapp01*> system led show Invalid command usage Usage: system led show <FRU-LED-ID>
Display status of the specified <FRU-LED-ID>.
<FRU-LED-ID>:
1 - SP Controller Fault LED 2 - SP Chassis Locate LED 3 - SP System Fault LED 4 - SP SAS Port A Fault LED 5 - SP SAS Port B Fault LED 6 - SP CNA 0 Port 1 Fault LED 7 - SP CNA 0 Port 2 Fault LED 8 - SP CNA 1 Port 1 Fault LED 9 - SP CNA 1 Port 2 Fault LED 10 - SP SFP Port 0 Fault LED 11 - SP SFP Port 1 Fault LED 12 - SP CPU DIMM 1 Fault LED 13 - SP CPU DIMM 2 Fault LED 14 - SP NVME 1 Fault LED 15 - SP MSATA Port Fault LED 16 - SP Battery Fault LED 17 - SP RTC Battery Fault LED (Coin Cell Battery) all others are not valid
SP netapp01*> SP netapp01*> SP netapp01*> system led show 1 FRU LED ID 1 is on SP netapp01*> system led show 2 FRU LED ID 2 is off SP netapp01*> system led show 3 FRU LED ID 3 is on. Set by SP SP netapp01*> system led show 4 FRU LED ID 4 is off SP netapp01*> system led show 5 FRU LED ID 5 is off SP netapp01*> system led show 6 FRU LED ID 6 is off SP netapp01*> system led show 7 FRU LED ID 7 is off SP netapp01*> system led show 8 FRU LED ID 8 is off SP netapp01*> system led show 9 FRU LED ID 9 is off SP netapp01*> system led show 10 FRU LED ID 10 is off SP netapp01*> system led show 11 FRU LED ID 11 is off SP netapp01*> system led show 12 FRU LED ID 12 is off SP netapp01*> system led show 13 FRU LED ID 13 is off SP netapp01*> system led show 14 FRU LED ID 14 is off SP netapp01*> system led show 15 FRU LED ID 15 is off SP netapp01*> system led show 16 FRU LED ID 16 is on SP netapp01*> system led show 17 FRU LED ID 17 is off
On the second controller, all LEDs (except for ID 3, which has been set by partner SP and is therefore related) are off. So thanks a bunch, I do at least finally know where this LED comes from ☺
Since this filer was unboxed today and installed, I’m not aware of any previous faults – could it be that the battery is almost empty and needs to fully charge? Any way to check the battery charging state?
Best,
Alexander Griesser Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.commailto:AGriesser@anexia-it.com Web: http://www.anexia-it.comhttp://www.anexia-it.com/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: Brad Thompson [mailto:brad.thompson877@gmail.commailto:brad.thompson877@gmail.com] Gesendet: Mittwoch, 14. Dezember 2016 22:39 An: Alexander Griesser <AGriesser@anexia-it.commailto:AGriesser@anexia-it.com> Cc: toasters@teaparty.netmailto:toasters@teaparty.net Betreff: Re: System attention LED
Is clustering enabled (cf status)? That will turn on the fault led if it's not enabled. What does "storage show fault" say? Other than that, the fault light could be on due to a previous fault in the system that has been cleared. Are you aware of any previous faults?
If you log in to the Service Processor you can run "priv set diag", followed by "system fru led show". That command will list out the available fru's that you can check the status on. For example:
SP nodeA*> system fru led show Invalid command usage Usage: system fru led show <FRU-LED-ID>
Display status of the specified <FRU-LED-ID>.
<FRU-LED-ID>:
0 = SP Controller Fault LED 1 = SP Heartbeat LED 2 = SP System Fault LED 3 = SP Fan 1 Fault LED 4 = SP Fan 2 Fault LED 5 = SP Fan 3 Fault LED 6 = SP IOXM Fault LED
all others are not valid
SP nodeA*> system fru led show 2 FRU LED ID 2 is off You can check the status of each fru id to see which one is on. From there double check there aren't any actual faults with that component. Still no faults? You may just be able to turn off the led using the "system fru led set" command.
On Wed, Dec 14, 2016 at 4:16 PM, Alexander Griesser <AGriesser@anexia-it.commailto:AGriesser@anexia-it.com> wrote: Hi there,
I have two filers (1x FAS2240 and 1x FAS2650) and both have the system attention LED lit and I have no idea why. `System health status show` as well as config advisor are both A-OK and there are no visible indicators why this LED is still lit.
Any idea how to find out the root cause of this LED on the front bezel or how I can check or maybe reset the status of the LED through CLI?
Thanks,
Alexander Griesser Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.commailto:AGriesser@anexia-it.com Web: http://www.anexia-it.comhttp://www.anexia-it.com/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
_______________________________________________ Toasters mailing list Toasters@teaparty.netmailto:Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters
_______________________________________________ Toasters mailing list Toasters@teaparty.netmailto:Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters