Thsts the one I was looking for
On Dec 14, 2016 5:11 PM, "Brad Thompson" brad.thompson877@gmail.com wrote:
The battery might be charging. check:
environment status chassis list-sensors
On Wed, Dec 14, 2016 at 4:49 PM, Alexander Griesser < AGriesser@anexia-it.com> wrote:
Hi Brad,
netapp01> storage show fault
No faults found in storage subsystem
netapp02> storage show fault
No faults found in storage subsystem
No luck with `system fru led show` on the SP of the 2650:
SP netapp01*> system fru led show
system fru show - display fru id inventory data
system fru list - list fru id
system fru log show - display fru log
system fru log clear - clear fru log
But this one seems to work (I’ve highlighted the ones where the LED seems to be in the „on“ state):
SP netapp01*> system led show
Invalid command usage
Usage: system led show <FRU-LED-ID>
Display status of the specified <FRU-LED-ID>.
<FRU-LED-ID>:
1 - SP Controller Fault LED 2 - SP Chassis Locate LED 3 - SP System Fault LED 4 - SP SAS Port A Fault LED 5 - SP SAS Port B Fault LED 6 - SP CNA 0 Port 1 Fault LED 7 - SP CNA 0 Port 2 Fault LED 8 - SP CNA 1 Port 1 Fault LED 9 - SP CNA 1 Port 2 Fault LED 10 - SP SFP Port 0 Fault LED 11 - SP SFP Port 1 Fault LED 12 - SP CPU DIMM 1 Fault LED 13 - SP CPU DIMM 2 Fault LED 14 - SP NVME 1 Fault LED 15 - SP MSATA Port Fault LED 16 - SP Battery Fault LED 17 - SP RTC Battery Fault LED (Coin Cell Battery) all others are not validSP netapp01*>
SP netapp01*>
SP netapp01*> system led show 1
FRU LED ID 1 is on
SP netapp01*> system led show 2
FRU LED ID 2 is off
SP netapp01*> system led show 3
FRU LED ID 3 is on. Set by SP
SP netapp01*> system led show 4
FRU LED ID 4 is off
SP netapp01*> system led show 5
FRU LED ID 5 is off
SP netapp01*> system led show 6
FRU LED ID 6 is off
SP netapp01*> system led show 7
FRU LED ID 7 is off
SP netapp01*> system led show 8
FRU LED ID 8 is off
SP netapp01*> system led show 9
FRU LED ID 9 is off
SP netapp01*> system led show 10
FRU LED ID 10 is off
SP netapp01*> system led show 11
FRU LED ID 11 is off
SP netapp01*> system led show 12
FRU LED ID 12 is off
SP netapp01*> system led show 13
FRU LED ID 13 is off
SP netapp01*> system led show 14
FRU LED ID 14 is off
SP netapp01*> system led show 15
FRU LED ID 15 is off
SP netapp01*> system led show 16
FRU LED ID 16 is on
SP netapp01*> system led show 17
FRU LED ID 17 is off
On the second controller, all LEDs (except for ID 3, which has been set by partner SP and is therefore related) are off.
So thanks a bunch, I do at least finally know where this LED comes from J
Since this filer was unboxed today and installed, I’m not aware of any previous faults – could it be that the battery is almost empty and needs to fully charge? Any way to check the battery charging state?
Best,
*Alexander Griesser*
Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.com
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
*Von:* Brad Thompson [mailto:brad.thompson877@gmail.com] *Gesendet:* Mittwoch, 14. Dezember 2016 22:39 *An:* Alexander Griesser AGriesser@anexia-it.com *Cc:* toasters@teaparty.net *Betreff:* Re: System attention LED
Is clustering enabled (cf status)? That will turn on the fault led if it's not enabled. What does "storage show fault" say? Other than that, the fault light could be on due to a previous fault in the system that has been cleared. Are you aware of any previous faults?
If you log in to the Service Processor you can run "priv set diag", followed by "system fru led show". That command will list out the available fru's that you can check the status on. For example:
SP nodeA*> system fru led show Invalid command usage Usage: system fru led show <FRU-LED-ID>
Display status of the specified <FRU-LED-ID>.
<FRU-LED-ID>:
0 = SP Controller Fault LED 1 = SP Heartbeat LED 2 = SP System Fault LED 3 = SP Fan 1 Fault LED 4 = SP Fan 2 Fault LED 5 = SP Fan 3 Fault LED 6 = SP IOXM Fault LED all others are not validSP nodeA*> system fru led show 2 FRU LED ID 2 is off
You can check the status of each fru id to see which one is on. From there double check there aren't any actual faults with that component. Still no faults? You may just be able to turn off the led using the "system fru led set" command.
On Wed, Dec 14, 2016 at 4:16 PM, Alexander Griesser < AGriesser@anexia-it.com> wrote:
Hi there,
I have two filers (1x FAS2240 and 1x FAS2650) and both have the system attention LED lit and I have no idea why.
`System health status show` as well as config advisor are both A-OK and there are no visible indicators why this LED is still lit.
Any idea how to find out the root cause of this LED on the front bezel or how I can check or maybe reset the status of the LED through CLI?
Thanks,
*Alexander Griesser*
Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.com
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Toasters mailing list Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters
Toasters mailing list Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters