Hi Milazzo,
thanks, the mediatype seems to be set to ptp already - I also cannot find a way to change that in CM, fcp config is not available on the node shell:
Node: jetfire Adapter: 1a Description: Fibre Channel Target Adapter 1a (QLogic 8324 (8362), rev. 2, 16G) Physical Protocol: fibre-channel Maximum Speed: 16 Status: link not connected Substatus: ADAPTER UP Host Port Address: 0 Firmware Revision: 6.10.0 Data Link Rate (Gbit): 0 Fabric Established: false Connection Established: loop Mediatype: ptp Configured Speed: auto Configured State: up Switch Port: :
Alexander Griesser System-Administrator
ANEXIA Internetdienstleistungs GmbH
Telefon: +43-5-0556-320 Telefax: +43-5-0556-500
E-Mail: ag@anexia.atmailto:ag@anexia.at Web: http://www.anexia.athttp://www.anexia.at/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: Milazzo Giacomo [mailto:G.Milazzo@sinergy.it] Gesendet: Montag, 09. Juni 2014 17:38 An: Alexander Griesser; Toasters Betreff: R: FCP Ports operational down
In your NetApp side I read: connection established "loop". It should be ptp for a fabric. Are you sure that your HBA on NetApp is well configured? It should be so by default but... On 7-Mode (on CM I don't remember)
1. fcp show adapter -v The current media type setting is displayed.
1. To change the setting of a target port to "ptp" for direct connections, enter the following commands at a storage system command prompt: fcp config adapter down fcp config adapter mediatype ptp fcp config adapter up
Da: toasters-bounces@teaparty.netmailto:toasters-bounces@teaparty.net [mailto:toasters-bounces@teaparty.net] Per conto di Alexander Griesser Inviato: lunedì 9 giugno 2014 15:35 A: Toasters Oggetto: FCP Ports operational down
Hi there,
I'm having a hard time currently connecting my new FAS8020 to our existing fabric - the FCP ports just won't get online and I'm not sure where exactly the problem is and how to debug that since I'm more the NAS guy not having much practical experience with FCP configurations, so here's the deal for all of you who are wanting to help.
FAS8020 Clustered Data Ontap 8.2.1 Brocade DS4900B
Brocade Switchport:
portcfgshow 0
Area Number: 0 Speed Level: AUTO(HW) Fill Word: 0(Idle-Idle) AL_PA Offset 13: OFF Trunk Port ON Long Distance OFF VC Link Init OFF Locked L_Port OFF Locked G_Port OFF Disabled E_Port OFF Locked E_Port OFF ISL R_RDY Mode OFF RSCN Suppressed OFF Persistent Disable OFF LOS TOV enable OFF NPIV capability ON QOS E_Port OFF Port Auto Disable: OFF Mirror Port OFF F_Port Buffers OFF Fault Delay: 0(R_A_TOV) NPIV PP Limit: 126
portshow 0
portIndex: 0 portName: portHealth: OFFLINE
Authentication: None portDisableReason: None portCFlags: 0x1 portFlags: 0x1 PRESENT U_PORT LocalSwcFlags: 0x0 portType: 10.0 POD Port: Port is licensed portState: 2 Offline Protocol: FC portPhys: 4 No_Light portScn: 0 port generation number: 0 state transition count: 0
portId: 010000 portIfId: 4302100d portWwn: 20:00:00:05:1e:5b:f9:a3 portWwn of device(s) connected:
Distance: normal portSpeed: N4Gbps
LE domain: 0 FC Fastwrite: OFF Interrupts: 2 Link_failure: 0 Frjt: 0 Unknown: 0 Loss_of_sync: 0 Fbsy: 0 Lli: 2 Loss_of_sig: 2 Proc_rqrd: 5 Protocol_err: 0 Timed_out: 0 Invalid_word: 0 Rx_flushed: 0 Invalid_crc: 0 Tx_unavail: 0 Delim_err: 0 Free_buffer: 0 Address_err: 0 Overrun: 0 Lr_in: 0 Suspended: 0 Lr_out: 0 Parity_err: 0 Ols_in: 0 2_parity_err: 0 Ols_out: 0 CMI_bus_err: 0
Port part of other ADs: No
FCP Adater on NetApp:
Node: jetfire Adapter: 1b Description: Fibre Channel Target Adapter 1b (QLogic 8324 (8362), rev. 2, 16G) Physical Protocol: fibre-channel Maximum Speed: 16 Status: link not connected Substatus: ADAPTER UP Host Port Address: 0 Firmware Revision: 6.10.0 Data Link Rate (Gbit): 0 Fabric Established: false Connection Established: loop Mediatype: ptp Configured Speed: 4 Configured State: up Switch Port: :
AFAIK, the 16Gbit/s adapter should be backwards compatible to 4Gbit/s, our switch only has 4Gbit/s but it supports NPIV which seems to be a requirement for running Clustered Data Ontap via FC.
So, I have no idea what information I should provide upfront for someone who's wanting to help me through get through that, but I'm more than happy to send more info when requested.
Thanks,
Alexander Griesser System-Administrator
ANEXIA Internetdienstleistungs GmbH
Telefon: +43-5-0556-320 Telefax: +43-5-0556-500
E-Mail: ag@anexia.atmailto:ag@anexia.at Web: http://www.anexia.athttp://www.anexia.at/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601