Re: disk ownership question

But to add to this - if you do want to allow autoassign to work, and have the disks in the ideal configuration, use the "disk replace" command to move specific disks in and out of aggregates to match the physical location requirements, or fully power down, and do a disk tango - pull them out and put them in the right place

Or, as Andrei said, leave as is and manually assign any replacement disks installed.

-- Alex Dawson | Solution Architect Scalar Decisions | 1100 Melville Street - Suite 750 - Vancouver BC - V6E 4A6 e: alex.dawson@scalar.ca | m: 604.763.4210

[Scalar Decisions Blog]https://www.scalar.ca/

The 2016 Scalar Security Study is here - get your copy nowhttps://www.scalar.ca/security-study-2016

________________________________ From: toasters-bounces@teaparty.net toasters-bounces@teaparty.net on behalf of andrei.borzenkov@ts.fujitsu.com andrei.borzenkov@ts.fujitsu.com Sent: Tuesday, March 22, 2016 5:11 AM To: Mark Flint; toasters@teaparty.net Subject: RE: disk ownership question

You are probably confused. Software based disk ownership indeed does not require that full loops/stacks or even shelves are assigned to the same filer. But for auto-assignment algorithm to work this is required. Later versions allow auto-assignment work for full shelves, thus you can mix full shelves from different filers on the same loop/stack. It is not default and has to be enabled.

So there is nothing to fix, it works as designed :) Actually I usually disable auto-assignment and do it manually, to be absolutely sure each disk belongs where it should.

---

With best regards

Andrei Borzenkov

Senior system engineer

FTS WEMEAI RUC RU SC TMS FOS

[cid:image001.gif@01CBF835.B3FEDA90]

FUJITSU

Zemlyanoy Val Street, 9, 105 064 Moscow, Russian Federation

Tel.: +7 495 730 62 20 ( reception)

Mob.: +7 916 678 7208

Fax: +7 495 730 62 14

E-mail: Andrei.Borzenkov@ts.fujitsu.commailto:Andrei.Borzenkov@ts.fujitsu.com

Web: ru.fujitsu.comhttp://ts.fujitsu.com/

Company details: ts.fujitsu.com/imprinthttp://ts.fujitsu.com/imprint.html

This communication contains information that is confidential, proprietary in nature and/or privileged. It is for the exclusive use of the intended recipient(s). If you are not the intended recipient(s) or the person responsible for delivering it to the intended recipient(s), please note that any form of dissemination, distribution or copying of this communication is strictly prohibited and may be unlawful. If you have received this communication in error, please immediately notify the sender and delete the original communication. Thank you for your cooperation.

Please be advised that neither Fujitsu, its affiliates, its employees or agents accept liability for any errors, omissions or damages caused by delays of receipt or by any virus infection in this message or its attachments, or which may otherwise arise as a result of this e-mail transmission.

From: toasters-bounces@teaparty.net [mailto:toasters-bounces@teaparty.net] On Behalf Of Mark Flint Sent: Tuesday, March 22, 2016 2:51 PM To: toasters@teaparty.net Subject: disk ownership question

Hi list. I have a 3170 running 8.0P1 7-Mode, and am having a problem with auto-assignment of disks. The unit reports that

it can't do auto-assign, because not all of the disks on the loop are owned by the same controller. I was under the impression

that software ownership made that unnecessary (you can laugh), but it seems not. KB from 2014 says the same thing. So,

question is, has anyone done anything like this (had to reassign a shedload of disks) to make auto-assign work, and could they

pass any info on how I can fix this please?

Thanks,

Mark