Hi Mike,
yes, I got it solved and wanted to reply back earlier but somehow always forgot about it :-/ I’m not really sure what finally was the fix, since I was having the filer in my lab when I encountered the issues and time ran out on the project to further debug this, so we shipped it to its final destination, powered it back on and everything was working. So I’m not sure i fit was the full halt of both filers to finally accept the NICs or i fit was a stronger guy than me who pushed in the QSFP+ modules (since the datacenter guy said that compared to the other modules in the servers f.ex., those had to be pushed in harder, whatever that means) and from then on, I was having full connectivity on all four modules in my gear.
I think I’ll never find out if it was me being to weak, or if the full powercycle helped it.
Best,
Alexander Griesser Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.commailto:AGriesser@anexia-it.com Web: http://www.anexia-it.comhttp://www.anexia-it.com/
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: Mike Thompson [mailto:mike.thompson@gmail.com] Gesendet: Sonntag, 2. April 2017 10:28 An: Alexander Griesser AGriesser@anexia-it.com Cc: toasters@teaparty.net Betreff: Re: X1144A - No link
Hey Alexander, Curious if you solved this issue.
I'm running into the same thing, but using copper QSFP NetApp cables. I have several FAS9000s with X91440A-C dual-port 40GbE cards, connecting to X190001 (Cisco 3132Q-V cluster net switches) via 3 meter copper X66100-3 40GbE QSFP cables. No link on either the filers, or the switches. The switches see the cables are inserted, but have status 'notconnec'. The ISL trunk connections between switches (ports 31/32 listed here) are working though: Ports 7 and 8 listed here are going back to the filers, and that's where I'm hoping to get link, but no luck.
pd-cluster-switch-2# show interface status -------------------------------------------------------------------------------- Port Name Status Vlan Duplex Speed Type -------------------------------------------------------------------------------- mgmt0 -- connected routed full 1000 -- Eth1/1/1 10GbE Node Port xcvrAbsen 1 auto auto -- Eth1/1/2 10GbE Node Port xcvrAbsen 1 auto auto -- ... Eth1/7 40GbE Node Port notconnec 1 auto auto QSFP-40G-CR4 Eth1/8 40GbE Node Port notconnec 1 auto auto QSFP-40G-CR4 Eth1/9 40GbE Node Port xcvrAbsen 1 auto auto -- Eth1/10 40GbE Node Port xcvrAbsen 1 auto auto -- ... Eth1/29 40GbE Node Port xcvrAbsen 1 auto auto -- Eth1/30 40GbE Node Port xcvrAbsen 1 auto auto -- Eth1/31 Inter-Cluster Swit connected trunk full 40G QSFP-40G-CR4 Eth1/32 Inter-Cluster Swit connected trunk full 40G QSFP-40G-CR4 Po1 -- connected trunk full 40G -- Sysconfig for the card in question:
slot 4: 40 Gigabit Ethernet Controller XL710 QSFP+ e4a MAC Address: 00:a0:98:c5:e3:3c (auto-unknown-down) e4e MAC Address: 00:a0:98:c5:e3:40 (auto-unknown-down) Device Type: XL710 B1 Firmware Version: nvm 5.04 etid 8000250c Part Number: 111-02590 Hardware Revision: A2 Serial Number: 031648001359 Just upgraded from 9.1 to 9.1p2 in hopes that might have some effect, but no change. I'm stumped.