Depending on workload, you can max out a single path (I have 4-Gbit DS14's and 3-Gbit DS4243's) Spreading the disks across more loops will give the potential to yield more bandwidth on the bigger heads (like my FAS6280's)
I routinely push 4-5 Gigabytes of bandwidth out of my Clustered Ontap 4-node system.
--tmac
*Tim McCarthy* *Principal Consultant*
Clustered ONTAP Clustered ONTAP NCDA ID: XK7R3GEKC1QQ2LVD RHCE5 805007643429572 NCSIE ID: C14QPHE21FR4YWD4 Expires: 08 November 2014 Expires w/release of RHEL7 Expires: 08 November 2014
On Thu, Dec 27, 2012 at 10:26 PM, Jeff Mohler speedtoys.racing@gmail.comwrote:
There is no 'shelf load'..just the # of disks in use for the workload irrespective of where they are.
Shelves just hold disks off the floor and provide power. :)
On Thu, Dec 27, 2012 at 9:20 PM, Bradley, Shane < shane.bradley@nz.fujitsu.com> wrote:
Hey****
Any reason why you choose to do it that way?****
I can’t really see what benefit you’re getting from splitting shelf loads between controllers.****
Cheers****
*Shane Bradley Senior Technical Consultant
Fujitsu New Zealand Limited* Level 12, Fujitsu Tower, 141 The Terrace, Wellington, New Zealand 6011 *T* +64 4 890 9605 *M* +64 21 229 1563 *F* +64 4 495 0730 shane.bradley@nz.fujitsu.com nz.fujitsu.com
*From:* toasters-bounces@teaparty.net [mailto: toasters-bounces@teaparty.net] *On Behalf Of *tmac *Sent:* Friday, 21 December 2012 2:38 p.m. *To:* Ray Van Dolson *Cc:* toasters@teaparty.net *Subject:* Re: Aggregate Best Practices****
Something I like to do to squeak out max performance is this:****
Between two heads, say I have 4 shelves.****
First and foremost, I try and make as many loops(FC)/stacks(SAS) as possible.****
Second, Each head will own half the disks in each shelf.****
So, from maintenance mode, on a new filer something along the likes of:** **
remove all disk ownerships from all heads.****
take owner ship of half the disks on head A****
(the logic is smart enough now where it almost always will grab****
roughly the same amount of disks from each shelf)****
take owner ship of the other half the disks on head B****
The only downside I see to this approach is when a disk fails,****
the admin must run a "disk assign" command to tell it when filer****
to belong to as no filer will own all the disks on any given shelf****
defeating the purpose of auto-assign based on ownership.****
So far, this method has been very good to me.****
--tmac****
*Tim McCarthy*****
*Principal Consultant*****
****
Clustered ONTAP Clustered ONTAP****
NCDA ID: XK7R3GEKC1QQ2LVD RHCE5 805007643429572 NCSIE ID: C14QPHE21FR4YWD4****
Expires: 08 November 2014 Expires w/release of RHEL7 Expires: 08 November 2014****
On Thu, Dec 20, 2012 at 8:28 PM, Ray Van Dolson rvandolson@esri.com wrote:
We're revisiting how we set up our aggregates and I want to see how others out there do it. Specifically, what strategies do you use for ensuring certain key applications or environments get the performance they need in a shared environment.
Typcially we'll create large aggregates based on a homogeneous disk type. 15K SAS disks in one aggregate, SATA in another. In some cases when it's only a single type of disk, we'd have 60 15K disks in one aggregate and 60 in other (assigned to each controller respectively).
The idea here is that more spindles gives us the most performance. However, some applications/workloads are more important than others, and some can be "bullies" impacting the important stuff. Ideally we'd try and keep our OLTP random workloads on one filer and heavy sequential workloads on another (maybe dedicated).
We've also been discussing creating multiple, smaller aggregates that we then assign to specific workloads guaranteting those spindles for those workloads. Lower possible maximum performance, but better protection against "bullies"[1].
I also know ONTAP has some I/O QoS options. I'm less inclined to go that direction however.
Our workloads tend to be ESX VM's using the filers as NFS datastores.
We have the usual budgetary / purchasing cycle constraints, so trying to minimize pain for as long as possible until we can add resources.
How do folks out there handle this?
Thanks, Ray
[1] Controller obviously still is shared. _______________________________________________ Toasters mailing list Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters****
Toasters mailing list Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters
--
Gustatus Similis Pullus _______________________________________________ Toasters mailing list Toasters@teaparty.net http://www.teaparty.net/mailman/listinfo/toasters
