What are you actually doing, more exactly? Sounds like it should be this:
- ssh admin@service-processor - system console - (log into system console) - system node run -node node1 “ndmpcopy…..”
You could also do "timeout modify -timeout 0" on the clustershell....just remember to set it back at some other point (default is 30)
Note you are *not* hitting the SSH timeout:
Autologout: System Console being disconnected due to inactivity
So doing the timeout above may be all you need.
--tmac
*Tim McCarthy, **Principal Consultant*
*Proud Member of the #NetAppATeam https://twitter.com/NetAppATeam*
*I Blog at TMACsRack https://tmacsrack.wordpress.com/*
On Tue, May 18, 2021 at 8:17 AM Heino Walther hw@beardmann.dk wrote:
Btw. Found this article describing the process: https://kb.netapp.com/Advice_and_Troubleshooting/Data_Protection_and_Securit...
Here is the “solution” as described in the article… the problem is that once I get the “disconnect” it does actually disconnect… maybe not from the Service-Processor, but it does disconnect the “node-shell” and the ndmpcopy process as a result…
I cannot find any timeout options in the service-processor options…. So not sure if I’m doing something wrong? I would think I am doing exactly as described below…
- Avoid SSH-related timeouts by running ndmpcopy from the console.
- To run ndmpcopy (or any command) from the console:
- First, find the IP of the service processor (SP) by running:
::> system service-processor show
After the IP of the SP is known, log in to the SP.
From the SP prompt, run system console to access the console.
Once at the system console prompt, re-run the ndmpcopy command from the
console.
*NOTE: *It is possible the connection to the system console will time out. Unlike a SSH session, any process started from system console will continue to run in the background.
- start ndmpcopy from the clustershell, via node run.
- *DO NOT *start ndmpcopy directly from nodeshell
The command I then run as point 4 is: node run -node node1 -command “ndmpcopy…..” and then wait…
So I’m at a loss here …
/Heino
*Fra: *Toasters toasters-bounces@teaparty.net på vegne af Heino Walther hw@beardmann.dk *Dato: *tirsdag, 18. maj 2021 kl. 13.59 *Til: *toasters@teaparty.net toasters@teaparty.net *Emne: *Ndmpcopy times out...
Hi guys
I have to migrate a large folder form one volume to another on the same system.
We are talking ONTAP 9.something, so the ndmpcopy is not a part of the cDot commandset, so the node shell have to be used…
The process runs and it starts to copy etc.. but after x-minutes the connection is terminated due to inactivity…
I have now tried to login to the service-processor, then “system console”, and then “node run -node node1 -command “ndmpcopy ….” And once again it starts, but is then terminated as my connection as shown here:
Ndmpcopy: 10.64.9.142: Log: DUMP: dumping (Pass IV) [regular files]
Ndmpcopy: 10.64.9.142: Log: RESTORE: Tue May 18 13:08:27 2021: Creating files and directories.
Ndmpcopy: 10.64.9.142: Log: RESTORE: Tue May 18 13:10:33 2021 : We have processed 298105 files and directories.
Ndmpcopy: 10.64.9.142: Log: RESTORE: Tue May 18 13:15:33 2021 : We have processed 508611 files and directories.
Ndmpcopy: 10.64.9.142: Log: RESTORE: Tue May 18 13:20:33 2021 : We have processed 693207 files and directories.
Ndmpcopy: 10.64.9.142: Log: RESTORE: Tue May 18 13:25:33 2021 : We have processed 860486 files and directories.
Autologout: System Console being disconnected due to inactivity
Any good suggestions are very welcome 😊
/Heino
Toasters mailing list Toasters@teaparty.net https://www.teaparty.net/mailman/listinfo/toasters