toasters

toasters@lists.teaparty.net

13531 discussions

Re: Disk auto assign
by Edward Rolison 12 Jun '15

12 Jun '15

Spot on - that's done the trick. Had '0a.01.0' with a foreign owner ID hiding in the list somewhere. I can only assume as part of a reboot/rebuild/pre-ship-test or something. Reassigned it to 'unowned' and all good. (well, a 'foreign aggr0(1)' showed up). On 11 June 2015 at 13:15, tmac <tmacmd(a)gmail.com> wrote: > SO, look at the output of disk show -a > The -n shows all non-owned disks. > > Look for disks not owned by either of your two nodes now. > If there are any disks owned by another party....ugh, little bit of work > involved. > > If not, do your best to verify which disks on which shelves are owned and > where. > > Sometimes it is helpful to run through the disks one by one, if possible, > use a sorting routine to put the disks in order to make looking at the list > easier. > > Let us know! > > > --tmac > > *Tim McCarthy* > *Principal Consultant* > > On Thu, Jun 11, 2015 at 8:12 AM, tmac <tmacmd(a)gmail.com> wrote: > >> any chance you can copy to a flash drive or the like? or is it more >> secure than that ;) >> >> >> --tmac >> >> *Tim McCarthy* >> *Principal Consultant* >> >> >> >> On Thu, Jun 11, 2015 at 8:11 AM, Edward Rolison <ed.rolison(a)gmail.com> >> wrote: >> >>> Sadly I can't - this is a system on an isolated network. I can re-type >>> parts of it, but that's probably not as useful. :/ >>> >>> On 11 June 2015 at 12:42, tmac <tmacmd(a)gmail.com> wrote: >>> >>>> Hey Edward, just for kicks, how about posting the "disk show -a" for us. >>>> >>>> Thanks >>>> >>>> --tmac >>>> >>>> *Tim McCarthy* >>>> *Principal Consultant* >>>> >>>> >>>> On Thu, Jun 11, 2015 at 7:26 AM, Edward Rolison <ed.rolison(a)gmail.com> >>>> wrote: >>>> >>>>> New disks are all listed in 'disk show -n'. I think that means they're >>>>> not assigned. (And a disk I've deliberately unassigned is also not being >>>>> reassigned). >>>>> >>>>> On 11 June 2015 at 12:12, Borzenkov, Andrei < >>>>> andrei.borzenkov(a)ts.fujitsu.com> wrote: >>>>> >>>>>> Are you sure new disks are unowned? It is not uncommon to get >>>>>> repurposed hardware. >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> *From:* Edward Rolison [mailto:ed.rolison@gmail.com] >>>>>> *Sent:* Thursday, June 11, 2015 2:09 PM >>>>>> *To:* Borzenkov, Andrei >>>>>> *Cc:* toasters(a)teaparty.net >>>>>> *Subject:* Re: Disk auto assign >>>>>> >>>>>> >>>>>> >>>>>> Sorry, should have said - also did this with the spares. I can see no >>>>>> drives on 'head1' sysconfig -r that are 'wrong' and likewise on 'head2'. >>>>>> >>>>>> >>>>>> Checked this with grepping 'partner' and ensuring they're all the >>>>>> right pair of controllers. (On both sides) >>>>>> >>>>>> >>>>>> >>>>>> On 11 June 2015 at 11:56, Borzenkov, Andrei < >>>>>> andrei.borzenkov(a)ts.fujitsu.com> wrote: >>>>>> >>>>>> If you just performed “replace” without un-/re-assigning drives that >>>>>> became spare, this is expected. Spares still belong to controller and will >>>>>> block auto assignment. >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> *From:* toasters-bounces(a)teaparty.net [mailto: >>>>>> toasters-bounces(a)teaparty.net] *On Behalf Of *Edward Rolison >>>>>> *Sent:* Thursday, June 11, 2015 1:09 PM >>>>>> *To:* toasters(a)teaparty.net >>>>>> *Subject:* Disk auto assign >>>>>> >>>>>> >>>>>> >>>>>> I've just added some new shelves to a (7-mode) filer pair, bring them >>>>>> up to two stacks of 10 shelves. >>>>>> >>>>>> I'm trying to get 'autoassign' working, and it isn't. >>>>>> >>>>>> I have: >>>>>> - swapped drives such that each 'head' has only disks from one >>>>>> 'stack'. >>>>>> >>>>>> Head 1 has 0a/5b >>>>>> >>>>>> Head 2 has 5a/5d >>>>>> >>>>>> >>>>>> >>>>>> I've had to manually trigger a small number of 'replace' operations. >>>>>> And then switched on autoassign in the options. >>>>>> >>>>>> I _think_ that should be it, but ... there's something I'm missing, >>>>>> because autoassign isn't working. >>>>>> >>>>>> >>>>>> >>>>>> Does anyone have suggestions for why this might be, or what else I >>>>>> could check? (I'm wondering if there's a misassigned but 'failed' drive >>>>>> that otherwise isn't showing up?) >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> Toasters mailing list >>>>> Toasters(a)teaparty.net >>>>> http://www.teaparty.net/mailman/listinfo/toasters >>>>> >>>>> >>>> >>> >> >

1 0

Multiple (more than 2) controllers in a cluster
by Philip Gardner, Jr. 11 Jun '15

11 Jun '15

Hi all - We are currently building out a new space (long time in the making), and some employees have come and go in between the process. We ended up with a 2240, a 3250, and an 8040. The 8040 is fully updated with CDOT 8.3. We are now preparing to do the same to the 2240 and 3250. The 2240 has the 10Gb mezzanine card, and the 3250 has two 10Gb PCI cards. I'm still learning, basically as I go, but does it make any sense to put all these filers in the same cluster? If not, does it make sense to use the CN1610's for each of the filers' cluster connections? I'm trying to think of a reason the 2240 needs to be in the same cluster, but can't really think of one. The 3250...maybe, since it is a decent amount of power. I know from some of the docs I've seen that the 2240 can use one of the 10Gb ports to connect to the other head in a non-redundant fashion, while still allowing the use of the other 10Gb ports for the data connection. Googling for things about multiple filers in the same cluster is difficult, or no one is talking about it. Thoughts or ideas? -- GPG keyID: 0xFECC890C Phil Gardner

3 4

Max number of hosts.
by Brad Thompson 11 Jun '15

11 Jun '15

Hi all, Has anyone ever seen these messages or know what causes them: lmgr.hosts.maxedout: Number of hosts active 50000 has reached the maximum number of hosts supported 50000. No additional host structures can be created. Thanks! Brad

3 3

Disk auto assign
by Edward Rolison 11 Jun '15

11 Jun '15

I've just added some new shelves to a (7-mode) filer pair, bring them up to two stacks of 10 shelves. I'm trying to get 'autoassign' working, and it isn't. I have: - swapped drives such that each 'head' has only disks from one 'stack'. Head 1 has 0a/5b Head 2 has 5a/5d I've had to manually trigger a small number of 'replace' operations. And then switched on autoassign in the options. I _think_ that should be it, but ... there's something I'm missing, because autoassign isn't working. Does anyone have suggestions for why this might be, or what else I could check? (I'm wondering if there's a misassigned but 'failed' drive that otherwise isn't showing up?)

3 9

cluster OS vs 7-mode
by Iluhes 11 Jun '15

11 Jun '15

For years I been complaining how much I dont like Cluster OS over 7-mode.I been telling netapp folks to keep 7 mode as an option and parallel OSThe storage field is evolving and there are so many more options now and reading this, looks like people are might voiting against cluster OS with their feet. Am I right? NetApp 4Q: Channel Sales Fall, Clustered Data OnTap Transition Tough, Layoffs Coming | | | | | | | | | | | NetApp 4Q: Channel Sales Fall, Clustered Data OnTap Tra...NetApp told analysts that fourth-quarter 2015 sales and earnings took a big hit because of a slower-than-expected transition of customers to the company's new Clust... | | | | View on www.crn.com | Preview by Yahoo | | | | |

8 8

Dedicated ONTAP disks?
by Fletcher Cocquyt 06 Jun '15

06 Jun '15

I’m curious how many admins dedicate 3 disks for ONTAP aggr0/vol0 vs having one big aggr0 and vol0 residing on the same aggr as the other data volumes? Is there a compelling reason to dedicate disks to ONTAP besides “best practice” ? thanks

5 4

RE: Dedicated ONTAP disks? (Fletcher Cocquyt)
by Woods, Bill 05 Jun '15

05 Jun '15

The latest install was configured with dedicated aggregates just for vol0 (NetApp Best Practice - especially for CDOT systems). If you have an issue where the aggregate containing vol0 (with data volumes) "drops-out" or loses multiple drives, you MAY NOT be able to recover that aggregate. Regards, Bill ------------------------------ Message: 3 Date: Fri, 5 Jun 2015 13:44:14 -0700 From: Fletcher Cocquyt <fcocquyt(a)stanford.edu> To: "<toasters(a)teaparty.net> Lists" <toasters(a)teaparty.net> Subject: Dedicated ONTAP disks? Message-ID: <77C0C02C-A86A-4EE8-B281-C41510845454(a)stanford.edu> Content-Type: text/plain; charset="utf-8" I?m curious how many admins dedicate 3 disks for ONTAP aggr0/vol0 vs having one big aggr0 and vol0 residing on the same aggr as the other data volumes? Is there a compelling reason to dedicate disks to ONTAP besides ?best practice? ? thanks

1 0

need some reallocate advice
by Rhodes, Richard L. 05 Jun '15

05 Jun '15

Hi, A bunch of IBM NSeries 3220 (NetApp FAS2240-2) OnTap 8.1.2p1 I'm about to start adding 2 disks to a bunch of NetApp systems - 2 disks into each system to expand CIFS shares. I will need to run reallocate to spread the vols in the expanded aggregates. There are around 30 vols in each aggr, some tiny and some a couple TB. Reallocate start -f -p /vol/<vol> How have you handled reallocate of a large number of vols in a aggr? Would you just start them all and let them run? If not doing them all at once, I could script them one at a time from AIX via ssh, but I don't see a "-w" (wait) option to allow easy single threading. I would need a loop to monitor for a particular reallocate cmd completes before starting another. I'd rather not get into that much scripting effort. Note that there is snapmirror and snapvault running every 6 hours on these vols. I don't want to hit the systems so hard that these have problems. Thanks! Rick ----------------------------------------- The information contained in this message is intended only for the personal and confidential use of the recipient(s) named above. If the reader of this message is not the intended recipient or an agent responsible for delivering it to the intended recipient, you are hereby notified that you have received this document in error and that any review, dissemination, distribution, or copying of this message is strictly prohibited. If you have received this communication in error, please notify us immediately, and delete the original message.

2 1

cDOT Transition Mirror
by Martin 29 May '15

29 May '15

Currently I have some Filers running 7.3.7P1 7-mode mirroring with VSM to 8.2.3P1 7-mode Filers for DR. I know in the event of failing over to the 8.2.3P1 Filers a failback would involve using something other than VSM (Robocopy, RSYNC) as we wouldn't be able to reverse the snapmirror from 8.2.3P1-->7.3.7P1. The 8.2.3P1 7-mode Filers are going to 8.3P1 cDOT but some of the 7.3.7P1 7-mode Filers are not due for replacement. I was considering using the transitional snapmirror (TDP) to mirror from the 7.3.7P1 7-mode Filers to the new cDOT Filers. I realise this is one way but this isn't any worse than the current situation. Has anyone used this configuration or see any issues with this? I'm trying to avoid having to provision a 7-mode DR Filer just for a couple of minor remote Filers. Thanks Martin -- View this message in context: http://network-appliance-toasters.10978.n7.nabble.com/cDOT-Transition-Mirro… Sent from the Network Appliance - Toasters mailing list archive at Nabble.com.

2 2

7-mode snapmirror question
by Basil 26 May '15

26 May '15

Hi folks, I have a 3170 running 7.3 snapmirroring volumes shared on vfiler0 to a 3250 running 8.2.1 7-mode. I want to start replicating a volume that needs to be owned by a vfiler on the 3170. Can I do that with the snapmirror service running on vfiler0? Or do I need to create a /etc/snapmirror.conf and all the other setup required inside the vfiler?

2 1

FAS8040: SP and e0M configuration
by Momonth 24 May '15

24 May '15

Hi All, I never used e0M on FAS32xx as it was limited to 100Mb, but decided to give a try on FAS8040. So, I've configured SP via DHCP (10.193.12.0/24), it's up and running and I can login onto it: na102::> sp show -node na102labnode-1a -instance Node: na102labnode-1a Type of Device: SP Status: online Is Network Configured: true Public IP Address: 10.193.12.31 MAC Address: 00:a0:98:68:00:18 Firmware Version: 3.1P1 Part Number: unknown Serial Number: unknown Device Revision: Not Applicable Is Firmware Autoupdate Enabled: true However having assigned an IP to e0M (from cluster management interface) doesn't make the e0M "ping-able". Here is my config (the same 10.193.12.0/24 is used): na102::> network interface show -vserver na102 -lif na102labnode-1a_mgmt1 -instance Vserver Name: na102 Logical Interface Name: na102labnode-1a_mgmt1 Role: node-mgmt Data Protocol: - Home Node: na102labnode-1a Home Port: e0M Current Node: na102labnode-1a Current Port: e0M Operational Status: up Extended Status: - Is Home: true Network Address: 10.193.12.44 Netmask: 255.255.255.0 Bits in the Netmask: 24 IPv4 Link Local: - Subnet Name: - Administrative Status: up Failover Policy: local-only Firewall Policy: mgmt Auto Revert: true Fully Qualified DNS Zone Name: none DNS Query Listen Enable: false Failover Group Name: Default FCP WWPN: - Address family: ipv4 Comment: - IPspace of LIF: Default It feels like e0M needs default gateway? How do I set it up then? Or Am I missing the whole idea here? Thanks, Vladimir

4 6

Linux OnCommand AD integration: group authentication
by Robb W. 22 May '15

22 May '15

Hi All, I have set up a couple of OnCommand servers to integrate with Windows AD for authentication. I used this NetApp Knowledge-base entry as my starting point: 1011398: How to configure OnCommand Unified Manager (Operations Manager) on Linux for authentication with Microsoft Active Directory The OnCommand servers are versions 5.2.1 (for 7-mode) and 6.2rc1 (for CDOT) respectively. Authentication of individual users accounts is working perfectly on both systems. But I cannot seem to get group based authentication to work ... On version 5.2.1 doing a "ldap find" returns this error: > linux:~ 22.05 15:07:00$ dfm ldap find Storage-Admin-Groupname > > Error: Searched under 'OU= ... ,' but didn't find administrator or group 'Storage-Admin-Groupname.' > > If 'Storage-Admin-Groupname' exists, one or more of these settings may be wrong: > ldapBaseDN, ldapUID, ldapGID, ldapUGID, ldapMember. > Templates can set all but ldapBaseDN to values that are probably compatible with your server. If I go ahead and add the group anyway, I get: > linux:~ 22.05 15:53:07$ dfm user add Storage-Admin-Groupname > > Warning: Storage-Admin-Groupname does not exist in the administrator database(s), so login is disabled for this administrator. > Added administrator Storage-Admin-Groupname. Doing a test operation via the version 6.2 Web UI returns a similar error. (Not surprisingly, since both systems are using the same settings.) Any tips on why this might not work, or suggestions on how to fix it? I assume that doing "dfm find group" like this should work? The (obfuscated) dfm options are as follows: ldapBaseDN OU=AdminUsers,OU=GlobalResources,OU=xxx,DC=yyy,DC=zzz,DC=xyz ldapBindDN oc-auth-account ldapBindPass ******** ldapEnabled Yes ldapGID memberOf ldapMember member ldapUGID CN ldapUID sAMAccountName ldapVersion 3 Thanks in advance for you help! Cheers, Robb.

2 1

Vol 100% - which VM?
by Fletcher Cocquyt 19 May '15

19 May '15

Never seen this before FAS3250 ONTAP 8.1.2 at 2am the volume hosting 110 VMs fills up and starts alerting Get the call and delete several snapshots to take it to 83%, reboot the 110 VMs ;( I have lots of tools (splunk, inmon etc) they are not able to show why this volume filled up ideas?

5 5

ONTAPI - perf-object-get-instances multiple
by Edward Rolison 15 May '15

15 May '15

I've been experimenting with ONTAPI for some monitoring. I've found it seems to support sending multiple API requests in a single POST - which is useful, because then I can fetch an XML bundle that contains 'system-get-info', 'clock-get-clock' and then 'perf-object-get-instances' for multiple objects. There's just one slight problem - when I do this, I get back a bunch of 'instance-data' elements, which aren't actually named as to which objects they're from - just which instance name. Has anyone else come up with a good solution to this? Are the counter names globally unique, and thus mappable back to their parent object? Or am I just going to have to accept making multiple requests, and fetch my perf counters separately?

1 0

AW: ACP - missing IOMs
by Alexander Griesser 14 May '15

14 May '15

Thanks everyone, since the filer is a few hundred kilometers away ATM I was hoping for a remote fix ☺ System is MPHA of course and I verified that with Config Advisor as well as on the CLI, so that shouldn’t be a problem. Does it make sense to open a Case to make them aware of the fact? Could that also be a firmware issue on the IOMs or ACP that might be fixed by applying a new firmware? I’m not sure how firmware updates are applied to the IOMs – is that happening through the SAS cables or is ACP necessary for that? My idea was to start a firmware update on the shelves to see if that fixes the issue, since a firmware update also reboots the IOMs one at a time – but if ACP connection is necessary for the FW update to complete I’m out of luck here and will have to dispatch remote hands. Best, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601 Von: Clark, André M. [mailto:Andre.Clark@redeight.com] Gesendet: Freitag, 08. Mai 2015 23:18 An: tmac; Alexander Griesser Cc: toasters(a)teaparty.net Betreff: RE: ACP - missing IOMs I’ve seen this issues on numerous installs now, including brand new systems. This is something that we should not have to be doing all the time. There has to be something else going on here. Regards, André M. Clark<mailto:Andre.Clark@redeight.com> | Sr. Solutions Architect | 917.388.8236 Tell me I will forget... Show me I may remember... Involve me I WILL UNDERSTAND!!! Start by doing what's necessary, then what's possible, and suddenly you are doing the impossible!!! Red8, An Insight Investments Company www.redeight.com<http://www.redeight.com/> From: toasters-bounces(a)teaparty.net<mailto:toasters-bounces@teaparty.net> [mailto:toasters-bounces@teaparty.net] On Behalf Of tmac Sent: Friday, 8 May, 2015 15:12 To: Alexander Griesser Cc: toasters(a)teaparty.net<mailto:toasters@teaparty.net> Subject: Re: ACP - missing IOMs Make sure your Multipath HA is working. go to shelf 23 and disconnect the B IOM from the backplane (no need to fully remove, just electrical disconnect) go to shelf 15 and disconnect the B IOM WAIT AT LEAST 4 MINUTES!!! Insert them back in to the shelves. Re-check after 15-20 minutes. That should do it. If there are still some missing, pull and wait at least 4 minutes. Make sure to only do one side (a or b) at a time! --tmac Tim McCarthy Principal Consultant On Fri, May 8, 2015 at 3:02 PM, Alexander Griesser <ag(a)anexia.at<mailto:ag@anexia.at>> wrote: Hey there, I was adding two shelves to one of my FAS8020s (cDOT, if that matters) recently and one IOM on each of the newly added shelves is missing in `storage show acp` or `acpadmin list_all` directly on the nodeshell. smokescreen> acpadmin list_all IP MAC Reset Last Contact Protocol Assigner Shelf Current Inband IOM Address Address Cnt (seconds ago) Version ACPA ID S/N State ID Type ---------------------------------------------------------------------------------------------------------------------- 192.168.0.1 00:a0:98:71:a0:00 000 163 1.2.2.8 536878789 SHFMS1414001364 0x5 0a.14.B IOM6 192.168.0.73 00:a0:98:72:d0:48 000 309 1.2.2.8 536878789 SHJMS1416001181 0x5 2a.21.B IOM6 192.168.0.101 00:a0:98:72:d0:64 000 373 1.2.2.8 536878789 SHJMS1416001174 0x5 2a.22.B IOM6 192.168.0.105 00:a0:98:72:d0:68 000 407 1.2.2.8 536878620 SHJMS1416001174 0x5 0b.22.A IOM6 192.168.0.191 00:a0:98:71:a0:be 000 154 1.2.2.8 536878789 SHFMS1414001364 0x5 2b.14.A IOM6 192.168.0.225 00:a0:98:83:14:e1 000 252 1.2.2.8 536878789 SHJHU1515000294 0x4 ------- IOM6 192.168.1.29 00:a0:98:72:d1:1c 000 335 1.2.2.8 536878789 SHJMS1416001181 0x5 0b.21.A IOM6 192.168.2.103 00:a0:98:83:12:67 000 251 1.2.2.8 536878789 SHJHU1515000294 0x5 0b.23.A IOM6 192.168.2.173 00:a0:98:72:ba:ac 000 392 1.2.2.8 536878789 SHFMS1417000556 0x5 2b.11.A IOM6 192.168.3.7 00:a0:98:72:cb:06 000 337 1.2.2.8 536878620 SHFMS1417000567 0x5 0a.12.B IOM6 192.168.3.13 00:a0:98:81:87:0c 000 384 1.2.2.8 536878789 SHFHU1513000260 0x4 ------- IOM6 192.168.3.19 00:a0:98:81:87:12 000 285 1.2.2.8 536878620 SHFHU1513000260 0x5 2b.15.A IOM6 192.168.3.21 00:a0:98:72:cb:14 000 407 1.2.2.8 536878789 SHFMS1417000567 0x5 2b.12.A IOM6 192.168.3.25 00:a0:98:72:2f:18 000 305 1.2.2.8 536878789 SHFMS1416000221 0x5 2b.13.A IOM6 192.168.3.95 00:a0:98:72:cb:5e 000 471 1.2.2.8 536878620 SHFMS1417000556 0x5 0a.11.B IOM6 192.168.3.131 00:a0:98:72:2f:82 000 386 1.2.2.8 536878789 SHFMS1416000221 0x5 0a.13.B IOM6 smokescreen> storage show acp Alternate Control Path: Enabled Ethernet Interface: e0P ACP Status: Active ACP IP Address: 192.168.2.215 ACP Subnet: 192.168.0.0 ACP Netmask: 255.255.252.0 ACP Connectivity Status: Additional Connectivity ACP Partner Connectivity Status: Additional Connectivity Shelf Module Reset Cnt IP Address FW Version Module Type Status ----------------- ------------ --------------- ------------ ------------ ------- 0b.23.A 000 192.168.2.103 02.08 IOM6 active 0b.21.A 000 192.168.1.29 02.08 IOM6 active 0b.22.A 000 192.168.0.105 02.08 IOM6 active 2b.15.A 000 192.168.3.19 02.08 IOM6 active 2b.12.A 000 192.168.3.21 02.08 IOM6 active 2b.14.A 000 192.168.0.191 02.08 IOM6 active 2b.11.A 000 192.168.2.173 02.08 IOM6 active 2b.13.A 000 192.168.3.25 02.08 IOM6 active 2a.21.B 000 192.168.0.73 02.08 IOM6 active 2a.22.B 000 192.168.0.101 02.08 IOM6 active 0a.14.B 000 192.168.0.1 02.08 IOM6 active 0a.13.B 000 192.168.3.131 02.08 IOM6 active 0a.12.B 000 192.168.3.7 02.08 IOM6 active 0a.11.B 000 192.168.3.95 02.08 IOM6 active NA 000 192.168.0.225 02.08 IOM6 inactive (no in-band connectivity) NA 000 192.168.3.13 02.08 IOM6 inactive (no in-band connectivity) I’ve done some research and found that usually a TO/GB helps in this situation, but I’m – of course – trying to avoid that. So, any ideas how I can try to make those pesky IOMs respond on the ACP? I tried to disable and re-enable ACP, but that didn’t help (maybe I did it wrong, have never fully disabled ACP on a cDOT system), so any pointers are welcome. Also, config advisor suggests to install missing shelf firmware, so I was wondering if it is safe to install the shelf firmware while an IOM is missing on the ACP? Thanks, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601 _______________________________________________ Toasters mailing list Toasters(a)teaparty.net<mailto:Toasters@teaparty.net> http://www.teaparty.net/mailman/listinfo/toasters

6 11

Using noninteractive ssh in Clustered Data Ontap
by Basil 14 May '15

14 May '15

I'm trying to use CDOT noninteractively from bash, but running into trouble. Let's say for example you wanted to get a list of volumes on an SVM and then sort by size- there's no sort in the interactive CLI and it asks you to enter text every page of results, so my initial thought was to send the command noninteractively and do what I need done in bash. If you send the command "ssh user@nas volume show -vserver whatever", you get a nicely formatted table without any of the line-splitting, confirmations, or other interactive shell nonsense: Vserver Volume Aggregate State Type Size Available Used% --------- ------------ ------------ ---------- ---- ---------- ---------- ----- svm vol1 aggr1 online RW 2TB 2.00TB 0% svm vol2 aggr1 online RW 100GB 100.00GB 0% This is much better, but I still can't use the size field to sort unless I can change it all to the same unit. If this were an interactive session, I'd use "set -units GB", however it's not. How can I accomplish that non-interactively? Can I send multiple commands in one ssh command? One thing that should work but doesn't is creating a list of commands that will run and sending them via ssh- me@myserver:/home/me $ cat temp set -units KB volume show -vserver svm -volume *root me@myserver:/home/me $ ssh admin@nas < temp Pseudo-terminal will not be allocated because stdin is not a terminal. nas::> set -units KB nas::> volume show -vserver svm -volume *root Vserver Volume Aggregate State Type Size Available Used% --------- ------------ ------------ ---------- ---- ---------- ---------- ----- svm svm_root aggr1 online RW 1048576KB 995796KB 5% nas::> me@myserver:/home/me $ As you see, as soon as it detects multiple lines, it switches back to the interactive shell. If I had use something with more than a single line of output, it would have given me a couple of lines, asked for "confirmation", and then exited. All the while putting "readability" whitespace inconsistently all over the results. Any ideas? Basil

8 13

Re: Using noninteractive ssh in Clustered Data Ontap
by Jeff VanDeRyt 14 May '15

14 May '15

In addition to the "set -units GB", we also do "rows 0" to get rid of the netapp line wrapping, and then "set -showseparator ~", so there is a known field separater - makes using awk to manipulate the data a lot easier. You can also use "-fields" on your commands so you only get the fields you are interested in: ssh -C -i $KEY user@$CONTROLLER "rows 0;set -showseparator ~;set -units GB;vol show -fields size" -Jeff ********************************************************** Electronic Mail is not secure, may not be read every day, and should not be used for urgent or sensitive issues

1 0

questions about converting 32 bit aggrs and the 7-Mode Transition Tool
by Rue, Randy 12 May '15

12 May '15

Hello All, We're replacing our v3170 with new gear (two clusters) and making the leap from 8.1.3 in 7-mode to 8.3 CDOT. I have a couple of questions around migrating our vFilers to the new cluster. Converting 32-bit aggrs: I see several places in NetApp's documentation saying the only way to convert in 8.1.3 is to expand the aggr to more than 16TB and it will happen automatically. I see references online to CLI commands that will set this off without needing to cross the 16TB line, and other references saying this is not recommended by NetApp or is even unsupported. And yet I have a co-worker here who converted a vFiler here when it outgrew 32-bit and swears a) expanding to 16TB did not spark the conversion and b) the CLI tool worked just fine. What is the official way to convert 32 bit to 64 bit? Second: how widely used is the 7-Mode Transition Tool? Got a candid opinion on how likely it is to be a better option than copying volumes by hand? Hope to hear from you, Randy

7 8

New error message
by Mark Flint 11 May '15

11 May '15

Or at least, one I’ve not seen before, anyway, error below, does anyone know what it’s referring to? fmmb.BlobNotFound: blob_id="3", owner="PARTNER", reason="no opaque data type" Thanks, ~Mark mark.flint(a)sanger.ac.uk

3 2

AW: AW: AW: ACP - missing IOMs
by Alexander Griesser 09 May '15

09 May '15

Hi Mayank, this HA pair is currently still running on: NetApp Release 8.2.1 Cluster-Mode Best, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601 Von: Saxena, Mayank [mailto:Mayank.Saxena@netapp.com] Gesendet: Samstag, 09. Mai 2015 18:56 An: Alexander Griesser; tmac; Borzenkov, Andrei Cc: Clark, André M.; toasters(a)teaparty.net Betreff: Re: AW: AW: ACP - missing IOMs Hi Alexander, Which Data ONTAP version you are running? ~Mayank From: Alexander Griesser <ag(a)anexia.at<mailto:ag@anexia.at>> Date: Saturday, May 9, 2015 at 5:17 AM To: tmac <tmacmd(a)gmail.com<mailto:tmacmd@gmail.com>>, "Borzenkov, Andrei" <andrei.borzenkov(a)ts.fujitsu.com<mailto:andrei.borzenkov@ts.fujitsu.com>> Cc: "Clark, André M." <Andre.Clark(a)redeight.com<mailto:Andre.Clark@redeight.com>>, "toasters(a)teaparty.net<mailto:toasters@teaparty.net>" <toasters(a)teaparty.net<mailto:toasters@teaparty.net>> Subject: AW: AW: ACP - missing IOMs Alright, thanks – I’ll go for the reseating then since this seems to be the most reliable solution which also shouldn’t have any other impact to the system. Best, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601 Von: tmac [mailto:tmacmd@gmail.com] Gesendet: Samstag, 09. Mai 2015 14:15 An: Borzenkov, Andrei Cc: Alexander Griesser; Clark, André M.; toasters(a)teaparty.net<mailto:toasters@teaparty.net> Betreff: Re: AW: ACP - missing IOMs The other method that seems to work every time that will work for you is a cluster takeover and giveback. I doubt rebooting the IOM will fix it. The two methods I have used that seem to work every time: 1. Pull the IOM for 4 minutes and re-insert (more details earlier in thread) 2. Takeover/Giveback. The short pull of the IOM was unreliable. Sometimes it worked, sometimes it did not and if it did not, it would usually cause other IOMS to misbehave for some reason. --tmac Tim McCarthy Principal Consultant On Sat, May 9, 2015 at 5:59 AM, Borzenkov, Andrei <andrei.borzenkov(a)ts.fujitsu.com<mailto:andrei.borzenkov@ts.fujitsu.com>> wrote: ACP is not necessary for FW update. There is also separate ACP firmware - here I am not sure whether it is update over SAS or Ethernet. There is also possibility to reboot IOM remotely, but you need to ask support how to do it. Отправлено с iPhone 9 мая 2015 г., в 11:25, Alexander Griesser <ag(a)anexia.at<mailto:ag@anexia.at>> написал(а): Thanks everyone, since the filer is a few hundred kilometers away ATM I was hoping for a remote fix ☺ System is MPHA of course and I verified that with Config Advisor as well as on the CLI, so that shouldn’t be a problem. Does it make sense to open a Case to make them aware of the fact? Could that also be a firmware issue on the IOMs or ACP that might be fixed by applying a new firmware? I’m not sure how firmware updates are applied to the IOMs – is that happening through the SAS cables or is ACP necessary for that? My idea was to start a firmware update on the shelves to see if that fixes the issue, since a firmware update also reboots the IOMs one at a time – but if ACP connection is necessary for the FW update to complete I’m out of luck here and will have to dispatch remote hands. Best, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601 Von: Clark, André M. [mailto:Andre.Clark@redeight.com] Gesendet: Freitag, 08. Mai 2015 23:18 An: tmac; Alexander Griesser Cc: toasters(a)teaparty.net<mailto:toasters@teaparty.net> Betreff: RE: ACP - missing IOMs I’ve seen this issues on numerous installs now, including brand new systems. This is something that we should not have to be doing all the time. There has to be something else going on here. Regards, André M. Clark<mailto:Andre.Clark@redeight.com>| Sr. Solutions Architect | 917.388.8236<tel:917.388.8236> Tell me I will forget... Show me I may remember... Involve me I WILL UNDERSTAND!!! Start by doing what's necessary, then what's possible, and suddenly you are doing the impossible!!! Red8, An Insight Investments Company www.redeight.com<http://www.redeight.com/> From:toasters-bounces@teaparty.net<mailto:toasters-bounces@teaparty.net> [mailto:toasters-bounces@teaparty.net] On Behalf Of tmac Sent: Friday, 8 May, 2015 15:12 To: Alexander Griesser Cc: toasters(a)teaparty.net<mailto:toasters@teaparty.net> Subject: Re: ACP - missing IOMs Make sure your Multipath HA is working. go to shelf 23 and disconnect the B IOM from the backplane (no need to fully remove, just electrical disconnect) go to shelf 15 and disconnect the B IOM WAIT AT LEAST 4 MINUTES!!! Insert them back in to the shelves. Re-check after 15-20 minutes. That should do it. If there are still some missing, pull and wait at least 4 minutes. Make sure to only do one side (a or b) at a time! --tmac Tim McCarthy Principal Consultant On Fri, May 8, 2015 at 3:02 PM, Alexander Griesser <ag(a)anexia.at<mailto:ag@anexia.at>> wrote: Hey there, I was adding two shelves to one of my FAS8020s (cDOT, if that matters) recently and one IOM on each of the newly added shelves is missing in `storage show acp` or `acpadmin list_all` directly on the nodeshell. smokescreen> acpadmin list_all IP MAC Reset Last Contact Protocol Assigner Shelf Current Inband IOM Address Address Cnt (seconds ago) Version ACPA ID S/N State ID Type ---------------------------------------------------------------------------------------------------------------------- 192.168.0.1 00:a0:98:71:a0:00 000 163 1.2.2.8 536878789 SHFMS1414001364 0x5 0a.14.B IOM6 192.168.0.73 00:a0:98:72:d0:48 000 309 1.2.2.8 536878789 SHJMS1416001181 0x5 2a.21.B IOM6 192.168.0.101 00:a0:98:72:d0:64 000 373 1.2.2.8 536878789 SHJMS1416001174 0x5 2a.22.B IOM6 192.168.0.105 00:a0:98:72:d0:68 000 407 1.2.2.8 536878620 SHJMS1416001174 0x5 0b.22.A IOM6 192.168.0.191 00:a0:98:71:a0:be 000 154 1.2.2.8 536878789 SHFMS1414001364 0x5 2b.14.A IOM6 192.168.0.225 00:a0:98:83:14:e1 000 252 1.2.2.8 536878789 SHJHU1515000294 0x4 ------- IOM6 192.168.1.29 00:a0:98:72:d1:1c 000 335 1.2.2.8 536878789 SHJMS1416001181 0x5 0b.21.A IOM6 192.168.2.103 00:a0:98:83:12:67 000 251 1.2.2.8 536878789 SHJHU1515000294 0x5 0b.23.A IOM6 192.168.2.173 00:a0:98:72:ba:ac 000 392 1.2.2.8 536878789 SHFMS1417000556 0x5 2b.11.A IOM6 192.168.3.7 00:a0:98:72:cb:06 000 337 1.2.2.8 536878620 SHFMS1417000567 0x5 0a.12.B IOM6 192.168.3.13 00:a0:98:81:87:0c 000 384 1.2.2.8 536878789 SHFHU1513000260 0x4 ------- IOM6 192.168.3.19 00:a0:98:81:87:12 000 285 1.2.2.8 536878620 SHFHU1513000260 0x5 2b.15.A IOM6 192.168.3.21 00:a0:98:72:cb:14 000 407 1.2.2.8 536878789 SHFMS1417000567 0x5 2b.12.A IOM6 192.168.3.25 00:a0:98:72:2f:18 000 305 1.2.2.8 536878789 SHFMS1416000221 0x5 2b.13.A IOM6 192.168.3.95 00:a0:98:72:cb:5e 000 471 1.2.2.8 536878620 SHFMS1417000556 0x5 0a.11.B IOM6 192.168.3.131 00:a0:98:72:2f:82 000 386 1.2.2.8 536878789 SHFMS1416000221 0x5 0a.13.B IOM6 smokescreen> storage show acp Alternate Control Path: Enabled Ethernet Interface: e0P ACP Status: Active ACP IP Address: 192.168.2.215 ACP Subnet: 192.168.0.0 ACP Netmask: 255.255.252.0 ACP Connectivity Status: Additional Connectivity ACP Partner Connectivity Status: Additional Connectivity Shelf Module Reset Cnt IP Address FW Version Module Type Status ----------------- ------------ --------------- ------------ ------------ ------- 0b.23.A 000 192.168.2.103 02.08 IOM6 active 0b.21.A 000 192.168.1.29 02.08 IOM6 active 0b.22.A 000 192.168.0.105 02.08 IOM6 active 2b.15.A 000 192.168.3.19 02.08 IOM6 active 2b.12.A 000 192.168.3.21 02.08 IOM6 active 2b.14.A 000 192.168.0.191 02.08 IOM6 active 2b.11.A 000 192.168.2.173 02.08 IOM6 active 2b.13.A 000 192.168.3.25 02.08 IOM6 active 2a.21.B 000 192.168.0.73 02.08 IOM6 active 2a.22.B 000 192.168.0.101 02.08 IOM6 active 0a.14.B 000 192.168.0.1 02.08 IOM6 active 0a.13.B 000 192.168.3.131 02.08 IOM6 active 0a.12.B 000 192.168.3.7 02.08 IOM6 active 0a.11.B 000 192.168.3.95 02.08 IOM6 active NA 000 192.168.0.225 02.08 IOM6 inactive (no in-band connectivity) NA 000 192.168.3.13 02.08 IOM6 inactive (no in-band connectivity) I’ve done some research and found that usually a TO/GB helps in this situation, but I’m – of course – trying to avoid that. So, any ideas how I can try to make those pesky IOMs respond on the ACP? I tried to disable and re-enable ACP, but that didn’t help (maybe I did it wrong, have never fully disabled ACP on a cDOT system), so any pointers are welcome. Also, config advisor suggests to install missing shelf firmware, so I was wondering if it is safe to install the shelf firmware while an IOM is missing on the ACP? Thanks, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601 _______________________________________________ Toasters mailing list Toasters(a)teaparty.net<mailto:Toasters@teaparty.net> http://www.teaparty.net/mailman/listinfo/toasters _______________________________________________ Toasters mailing list Toasters(a)teaparty.net<mailto:Toasters@teaparty.net> http://www.teaparty.net/mailman/listinfo/toasters

1 0

Re: 2 Drives support with cmode 8.3
by Ashwin Pawar 08 May '15

08 May '15

Hi Francis / Friends, Honestly that's all information I have. It was a long & crazy day for me and therefore I really didn't bothered to investigate much from the customer. But it does seem like no brainier :) Story goes like this: One of my customer wrote us [CommVault] saying with cluster 8.2 they could use only Tape Drive with at a given time with NDMP, however NetApp has confirmed to them that with 8.3 they can utilize both drives. So they wanted to know if CommVault support this or not. I am now totally confused what did he mean Drive [Spinning] or Tape Drive, but I think there is no restriction for the number of drives that you can write to, it depends upon how many streams you are reading from the NetApp filer. Therefore I am just little baffled by what he actually meant. I just thought of asking the community if they are aware of any such thing. Thanks, -Ashwin On Fri, May 8, 2015 at 8:02 PM, <toasters-request(a)teaparty.net> wrote: > Send Toasters mailing list submissions to > toasters(a)teaparty.net > > To subscribe or unsubscribe via the World Wide Web, visit > http://www.teaparty.net/mailman/listinfo/toasters > or, via email, send a message with subject or body 'help' to > toasters-request(a)teaparty.net > > You can reach the person managing the list at > toasters-owner(a)teaparty.net > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Toasters digest..." > > > Today's Topics: > > 1. Re: Toasters Digest, Vol 46, Issue 5 (Martin) > 2. Re: Toasters Digest, Vol 46, Issue 5 (Francis Kim) > 3. ACP - missing IOMs (Alexander Griesser) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Fri, 8 May 2015 07:45:39 -0700 (MST) > From: Martin <martin(a)leggatt.me.uk> > To: toasters(a)teaparty.net > Subject: Re: Toasters Digest, Vol 46, Issue 5 > Message-ID: <1431096339376-26625.post(a)n7.nabble.com> > Content-Type: text/plain; charset=us-ascii > > Hi Ashwin, > > I think you'll need to provide a bit more detail to get a response on this. > > 2 drives for what purpose on a cDOT Cluster? > > > > -- > View this message in context: > http://network-appliance-toasters.10978.n7.nabble.com/Re-Toasters-Digest-Vo… > Sent from the Network Appliance - Toasters mailing list archive at > Nabble.com. > > > ------------------------------ > > Message: 2 > Date: Fri, 8 May 2015 16:33:51 +0000 > From: Francis Kim <fkim(a)BERKCOM.com> > To: Martin <martin(a)leggatt.me.uk> > Cc: "toasters(a)teaparty.net" <toasters(a)teaparty.net> > Subject: Re: Toasters Digest, Vol 46, Issue 5 > Message-ID: <88E2EFC1-5FE1-472E-9E43-8C9D399FBF62(a)berkcom.com> > Content-Type: text/plain; charset="utf-8" > > Ashwin, > > Yes, you can create a 2 drive aggregate in cDOT. > > However, if you?re interested in 2 drive aggregates for the purposes of > minimizing the amount of capacity you have to devote to the root aggregate, > a better approach might be to leverage the root-data partitioning > capability, available for entry-level and AFF platforms, running DataONTAP > 8.3. > > Francis Kim | Engineer > 510-644-1599 x334 | fkim(a)berkcom.com<mailto:fkim@berkcom.com> > > BerkCom | www.berkcom.com<http://www.berkcom.com/> > NetApp | Cisco | Supermicro | Brocade | VMware > > On May 8, 2015, at 7:45 AM, Martin <martin(a)leggatt.me.uk<mailto: > martin(a)leggatt.me.uk>> wrote: > > Hi Ashwin, > > I think you'll need to provide a bit more detail to get a response on this. > > 2 drives for what purpose on a cDOT Cluster? > > > > -- > View this message in context: > http://network-appliance-toasters.10978.n7.nabble.com/Re-Toasters-Digest-Vo… > Sent from the Network Appliance - Toasters mailing list archive at > Nabble.com<http://Nabble.com>. > _______________________________________________ > Toasters mailing list > Toasters(a)teaparty.net<mailto:Toasters@teaparty.net> > http://www.teaparty.net/mailman/listinfo/toasters > >

1 0

ACP - missing IOMs
by Alexander Griesser 08 May '15

08 May '15

Hey there, I was adding two shelves to one of my FAS8020s (cDOT, if that matters) recently and one IOM on each of the newly added shelves is missing in `storage show acp` or `acpadmin list_all` directly on the nodeshell. smokescreen> acpadmin list_all IP MAC Reset Last Contact Protocol Assigner Shelf Current Inband IOM Address Address Cnt (seconds ago) Version ACPA ID S/N State ID Type ---------------------------------------------------------------------------------------------------------------------- 192.168.0.1 00:a0:98:71:a0:00 000 163 1.2.2.8 536878789 SHFMS1414001364 0x5 0a.14.B IOM6 192.168.0.73 00:a0:98:72:d0:48 000 309 1.2.2.8 536878789 SHJMS1416001181 0x5 2a.21.B IOM6 192.168.0.101 00:a0:98:72:d0:64 000 373 1.2.2.8 536878789 SHJMS1416001174 0x5 2a.22.B IOM6 192.168.0.105 00:a0:98:72:d0:68 000 407 1.2.2.8 536878620 SHJMS1416001174 0x5 0b.22.A IOM6 192.168.0.191 00:a0:98:71:a0:be 000 154 1.2.2.8 536878789 SHFMS1414001364 0x5 2b.14.A IOM6 192.168.0.225 00:a0:98:83:14:e1 000 252 1.2.2.8 536878789 SHJHU1515000294 0x4 ------- IOM6 192.168.1.29 00:a0:98:72:d1:1c 000 335 1.2.2.8 536878789 SHJMS1416001181 0x5 0b.21.A IOM6 192.168.2.103 00:a0:98:83:12:67 000 251 1.2.2.8 536878789 SHJHU1515000294 0x5 0b.23.A IOM6 192.168.2.173 00:a0:98:72:ba:ac 000 392 1.2.2.8 536878789 SHFMS1417000556 0x5 2b.11.A IOM6 192.168.3.7 00:a0:98:72:cb:06 000 337 1.2.2.8 536878620 SHFMS1417000567 0x5 0a.12.B IOM6 192.168.3.13 00:a0:98:81:87:0c 000 384 1.2.2.8 536878789 SHFHU1513000260 0x4 ------- IOM6 192.168.3.19 00:a0:98:81:87:12 000 285 1.2.2.8 536878620 SHFHU1513000260 0x5 2b.15.A IOM6 192.168.3.21 00:a0:98:72:cb:14 000 407 1.2.2.8 536878789 SHFMS1417000567 0x5 2b.12.A IOM6 192.168.3.25 00:a0:98:72:2f:18 000 305 1.2.2.8 536878789 SHFMS1416000221 0x5 2b.13.A IOM6 192.168.3.95 00:a0:98:72:cb:5e 000 471 1.2.2.8 536878620 SHFMS1417000556 0x5 0a.11.B IOM6 192.168.3.131 00:a0:98:72:2f:82 000 386 1.2.2.8 536878789 SHFMS1416000221 0x5 0a.13.B IOM6 smokescreen> storage show acp Alternate Control Path: Enabled Ethernet Interface: e0P ACP Status: Active ACP IP Address: 192.168.2.215 ACP Subnet: 192.168.0.0 ACP Netmask: 255.255.252.0 ACP Connectivity Status: Additional Connectivity ACP Partner Connectivity Status: Additional Connectivity Shelf Module Reset Cnt IP Address FW Version Module Type Status ----------------- ------------ --------------- ------------ ------------ ------- 0b.23.A 000 192.168.2.103 02.08 IOM6 active 0b.21.A 000 192.168.1.29 02.08 IOM6 active 0b.22.A 000 192.168.0.105 02.08 IOM6 active 2b.15.A 000 192.168.3.19 02.08 IOM6 active 2b.12.A 000 192.168.3.21 02.08 IOM6 active 2b.14.A 000 192.168.0.191 02.08 IOM6 active 2b.11.A 000 192.168.2.173 02.08 IOM6 active 2b.13.A 000 192.168.3.25 02.08 IOM6 active 2a.21.B 000 192.168.0.73 02.08 IOM6 active 2a.22.B 000 192.168.0.101 02.08 IOM6 active 0a.14.B 000 192.168.0.1 02.08 IOM6 active 0a.13.B 000 192.168.3.131 02.08 IOM6 active 0a.12.B 000 192.168.3.7 02.08 IOM6 active 0a.11.B 000 192.168.3.95 02.08 IOM6 active NA 000 192.168.0.225 02.08 IOM6 inactive (no in-band connectivity) NA 000 192.168.3.13 02.08 IOM6 inactive (no in-band connectivity) I've done some research and found that usually a TO/GB helps in this situation, but I'm - of course - trying to avoid that. So, any ideas how I can try to make those pesky IOMs respond on the ACP? I tried to disable and re-enable ACP, but that didn't help (maybe I did it wrong, have never fully disabled ACP on a cDOT system), so any pointers are welcome. Also, config advisor suggests to install missing shelf firmware, so I was wondering if it is safe to install the shelf firmware while an IOM is missing on the ACP? Thanks, Alexander Griesser Head of Systems Operations ANEXIA Internetdienstleistungs GmbH E-Mail: ag(a)anexia.at<mailto:ag@anexia.at> Web: http://www.anexia.at<http://www.anexia.at/> Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt Geschäftsführer: Alexander Windbichler Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

4 3

Re: Toasters Digest, Vol 46, Issue 5
by Ashwin Pawar 08 May '15

08 May '15

Hi Community, I have this query, can someone provide more information on this. Ability to utilize 2 drives on a filer with Ontap cluster 8.3 ? Thanks, -Ashwin On Thu, May 7, 2015 at 12:00 PM, <toasters-request(a)teaparty.net> wrote: > Send Toasters mailing list submissions to > toasters(a)teaparty.net > > To subscribe or unsubscribe via the World Wide Web, visit > http://www.teaparty.net/mailman/listinfo/toasters > or, via email, send a message with subject or body 'help' to > toasters-request(a)teaparty.net > > You can reach the person managing the list at > toasters-owner(a)teaparty.net > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Toasters digest..." > > > Today's Topics: > > 1. New error message (Mark Flint) > 2. RE: New error message (Borzenkov, Andrei) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Wed, 6 May 2015 15:19:03 +0100 > From: Mark Flint <mf1(a)sanger.ac.uk> > To: Toasters <toasters(a)teaparty.net> > Subject: New error message > Message-ID: <7BF26AD4-5A1C-488A-B416-E254F6D7BE04(a)sanger.ac.uk> > Content-Type: text/plain; charset="windows-1252" > > Or at least, one I?ve not seen before, anyway, error below, does anyone > know what > it?s referring to? > > fmmb.BlobNotFound: blob_id="3", owner="PARTNER", reason="no opaque data > type" > > Thanks, > > ~Mark > > mark.flint(a)sanger.ac.uk > > >

3 2

Retiring an Exchange dataset?
by James Andrewartha 08 May '15

08 May '15

Hi list, We've recently upgraded our Exchange install from 2007 to 2013. As part of this I did a fresh install of SME 7.1.1 on the new mailbox server, which created a new dataset. With all the user data migrated off the off the old mailbox server, I now have a dataset full of archive information. Is there any way to keep it around in case I ever need to restore from it with SMBR, but uninstall Exchange from the mailbox server? Will SME still keep the backup information in that case? Could I maybe just reinstall the management tools? Also, I unmounted the LUNs, moved the volumes to a SATA disks on a different filer using SnapMirror, updated the SnapVault relationship and remounted the LUNs, which worked fine. The dataset itself didn't recognise this update however, and now it's complaining it can't create relationships. Can I just delete the dataset from DFM? Will that delete the data or leave it around? Thanks, -- James Andrewartha Network & Projects Engineer Christ Church Grammar School Claremont, Western Australia Ph. (08) 9442 1757 Mob. 0424 160 877

2 2

Netapp 4 node cluster aggregate question
by Basil 07 May '15

07 May '15

Hi folks, If I have a 4 node cluster (running 8.2 CDOT) and I want to install 5 shelves of 10k SAS and 5 shelves of 7.2k drives, what would you recommend I do regarding aggregates? Normally on a 2 node cluster, we'd put all the SAS on one node and all the SATA on the other one. In this case, should we ensure that each node has an aggregate and attempt to avoid using the cluster network as much as possible? The work being done is file shares and NDMP backups, both of which tend to run out of CPU and memory before they redline the backend disks. We want to use the processing of all four nodes, so that means we'll be spreading the LIFs across them all. Thanks!

2 1

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

toasters