I've got exactly the same issue with FAS8040 4 nodes cluster, running
8.2.1 and 8.2.2
However it's not HBA HW related as I've got similar cluster in 2nd DC
and it works just fine with the same HBA on filers.
On-board ports (I don't have any SAN svm configured):
na101::*> network fcp adapter show -node na101node-* -fields
switch-port,fc-wwpn -adapter 0e
node adapter fc-wwpn switch-port
------------ ------- ----------------------- --------------
na101node-1a 0e 50:0a:09:87:80:71:20:df fca-core-101:0
na101node-1b 0e 50:0a:09:87:80:01:21:93 fca-core-101:1
na101node-2a 0e 50:0a:09:87:80:01:1f:7f fca-core-101:40
na101node-2b 0e 50:0a:09:87:80:01:20:9e fca-core-101:41
4 entries were displayed.
Slot 3 ports:
na101::*> network fcp adapter show -node na101node-* -fields
switch-port,fc-wwpn -adapter 3a
node adapter fc-wwpn switch-port
------------ ------- ----------------------- -----------
na101node-1a 3a 50:0a:09:81:80:71:20:df :
na101node-1b 3a 50:0a:09:81:80:01:21:93 :
na101node-2a 3a 50:0a:09:81:80:01:1f:7f :
na101node-2b 3a 50:0a:09:81:80:01:20:9e :
4 entries were displayed.
I just upgraded to 8.2.2 and it didn't resolve the issue.
Some more details:
fcb-core-101:FID128:admin> portcfgshow 40
Area Number: 40
Octet Speed Combo: 1(16G|8G|4G|2G)
Speed Level: AUTO(SW)
AL_PA Offset 13: OFF
Trunk Port ON
Long Distance OFF
VC Link Init OFF
Locked L_Port OFF
Locked G_Port OFF
Disabled E_Port OFF
Locked E_Port OFF
ISL R_RDY Mode OFF
RSCN Suppressed OFF
Persistent Disable OFF
LOS TOV enable OFF
NPIV capability ON
QOS E_Port AE
Port Auto Disable: OFF
Rate Limit OFF
EX Port OFF
Mirror Port OFF
Credit Recovery ON
F_Port Buffers OFF
Fault Delay: 0(R_A_TOV)
NPIV PP Limit: 255
CSCTL mode: OFF
D-Port mode: OFF
Compression: OFF
Encryption: OFF
FEC: ON
fcb-core-101:FID128:admin> portshow 40
portIndex: 40
portName: na101node-2a_3a
portHealth: No Fabric Watch License
Authentication: None
portDisableReason: None
portCFlags: 0x1
portFlags: 0x24b03 PRESENT ACTIVE F_PORT G_PORT U_PORT LOGICAL_ONLINE
LOGIN NOELP LED ACCEPT FLOGI
LocalSwcFlags: 0x0
portType: 24.0
POD Port: Port is licensed
portState: 1 Online
Protocol: FC
portPhys: 6 In_Sync portScn: 32 F_Port
port generation number: 114
state transition count: 7
portId: c92800
portIfId: 4302001e
portWwn: 20:28:00:27:f8:bd:ec:1c
portWwn of device(s) connected:
21:00:00:24:ff:73:20:73
Distance: normal
portSpeed: N8Gbps
FEC: Inactive
LE domain: 0
FC Fastwrite: OFF
Interrupts: 0 Link_failure: 3 Frjt: 0
Unknown: 0 Loss_of_sync: 4 Fbsy: 0
Lli: 31 Loss_of_sig: 7
Proc_rqrd: 32 Protocol_err: 0
Timed_out: 0 Invalid_word: 0
Rx_flushed: 0 Invalid_crc: 0
Tx_unavail: 0 Delim_err: 0
Free_buffer: 0 Address_err: 0
Overrun: 0 Lr_in: 4
Suspended: 0 Lr_out: 4
Parity_err: 0 Ols_in: 4
2_parity_err: 0 Ols_out: 4
CMI_bus_err: 0
na101::*> ucadmin show -node na101node-2a -adapter 3a -instance
Node: na101node-2a
Adapter: 3a
Current Mode: fc
Current Type: target
Pending Mode: -
Pending Type: -
Status: online
Supported Modes: fc
Supported FC Types: initiator, target
Supported CNA Types: -
It feels like Im missing something obvious .. any help is appreciated.
Cheers,
Vladimir
On Tue, Jun 17, 2014 at 7:40 AM, Alexander Griesser <ag@anexia.at> wrote:
> No part numbers on them, I did also check.
> You can just see the SFP manufacturer + model in the sysconfig -a output, but that's about it - no indication of whether they're compatible with what card or something like this.
>
> Support is working through the new CA output now and will update me if on the SAS cabling issue afterwards, all other warnings in CA 3.5 are just related to firmware (new one got released) and port mismatch which is to be expected at the moment since I'm running an asymmetric configuration right now.
>
> Best,
>
> Alexander Griesser
> System-Administrator
>
_______________________________________________
Toasters mailing list
Toasters@teaparty.net
http://www.teaparty.net/mailman/listinfo/toasters