Hi,
just as a follow up – I upgraded the FAS2240 to 8.2.4P5 including all the SP firmware update etc. and the LED was still on; I also
halted the systems each and LED was still on, but on 8.2.4P5, the FRU LED commands changed and showed different values.
On the filer in question, it now showed „NV-DIMM“ error LED on one controller and then I openend up a support case (remember, previously
it was „SP interconnect error“).
Support walked me through a few commands and had me send some Autosupports and we finally agreed that there is no error and we have
reset the LEDs then and since then they’ve been off and I hope it will stay like this
J
Next up: FAS2650 which still hast he LED turned on without any obvious reason to me, so I think I’ll also open up a case on this one
unless someone has a good idea…
Best,
Alexander Griesser
Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail:
AGriesser@anexia-it.com
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: andrei.borzenkov@ts.fujitsu.com [mailto:andrei.borzenkov@ts.fujitsu.com]
Gesendet: Donnerstag, 15. Dezember 2016 17:37
An: Alexander Griesser <AGriesser@anexia-it.com>
Cc: jordan slingerland <jordan.slingerland@gmail.com>; toasters@teaparty.net
Betreff: Re: AW: AW: AW: System attention LED
On the node that has LED on. If both are affected, you can do this one after another with usual takeover/giveback.
Отправлено с iPhone
15 дек. 2016 г., в 19:17, Alexander Griesser <AGriesser@anexia-it.com> написал(а):
Yah, read that – but what I’m unsure about: Do both nodes need to be halted at the same time (aka downtime for the customer) or can I do them one after the other?
Alexander Griesser
Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.com
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: andrei.borzenkov@ts.fujitsu.com [mailto:andrei.borzenkov@ts.fujitsu.com]
Gesendet: Donnerstag, 15. Dezember 2016 17:12
An: Alexander Griesser <AGriesser@anexia-it.com>
Cc: jordan slingerland <jordan.slingerland@gmail.com>; toasters@teaparty.net
Betreff: Re: AW: AW: System attention LED
In 7-Mode "halt -s" was known to clear stray alarm LED. Not sure what is equivalent in C-Mode.
Отправлено с iPhone
15 дек. 2016 г., в 15:46, Alexander Griesser <AGriesser@anexia-it.com> написал(а):Hi,
the LED is still on and I guess it should have been fully charged by now if this would have been the issue.
So, any other ideas besides opening a case?
Regarding the FAS2240 I mentioned in my initial e-mail:
SP netapp1*> system fru led show 0
FRU LED ID 0 is off
SP netapp1*> system fru led show 1
FRU LED ID 1 is on
I did google a bit for this symptom and therefore updated the SP firmware to the latest compatible one for my ontap version (2.1.3P2), but that did not fix the issue.
Any fix for this symptom except for halting both nodes?
Best,
Alexander Griesser
Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.com
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: toasters-bounces@teaparty.net [mailto:toasters-bounces@teaparty.net] Im Auftrag von Alexander Griesser
Gesendet: Mittwoch, 14. Dezember 2016 23:29
An: jordan slingerland <jordan.slingerland@gmail.com>
Cc: toasters@teaparty.net
Betreff: AW: AW: System attention LED
Maybe that has changed with OnTap 9.1? I’m running 9.1RC2 here on this filer and not because I’m brave, but because it got shipped with it J
Alexander Griesser
Head of Systems Operations
ANEXIA Internetdienstleistungs GmbH
E-Mail: AGriesser@anexia-it.com
Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601
Von: jordan slingerland [mailto:jordan.slingerland@gmail.com]
Gesendet: Mittwoch, 14. Dezember 2016 23:27
An: Alexander Griesser <AGriesser@anexia-it.com>
Cc: toasters@teaparty.net; Brad Thompson <brad.thompson877@gmail.com>
Betreff: Re: AW: System attention LED
Hmm, expected it to look like this listing charge voltage. Current and hours it can hold