Hi Alexander,

I ran into the problem you described on a FAS2650 HA pair with the following LEDs on on one node (all other LEDs were off):

SP snae-bruntp07-01*> system led show 1
FRU LED ID 1 is on
SP snae-bruntp07-01*> system led show 3
FRU LED ID 3 is on. Set by SP
SP snae-bruntp07-01*> system led show 16
FRU LED ID 16 is on

And no signs of any problems from the CLI environment commands in ONTAP and the SP.

As per a suggestion on this thread, I performed a halt -s on the node and reseated both the controller module and two PSU modules.
After a boot and giveback the LEDs are now cleared. Good luck!

Best regards,
Filip


On Tue, Dec 20, 2016 at 10:29 PM, Alexander Griesser <AGriesser@anexia-it.com> wrote:

Hi,

 

just as a follow up – I upgraded the FAS2240 to 8.2.4P5 including all the SP firmware update etc. and the LED was still on; I also halted the systems each and LED was still on, but on 8.2.4P5, the FRU LED commands changed and showed different values.

On the filer in question, it now showed „NV-DIMM“ error LED on one controller and then I openend up a support case (remember, previously it was „SP interconnect error“).

Support walked me through a few commands and had me send some Autosupports and we finally agreed that there is no error and we have reset the LEDs then and since then they’ve been off and I hope it will stay like this J

 

Next up: FAS2650 which still hast he LED turned on without any obvious reason to me, so I think I’ll also open up a case on this one unless someone has a good idea…

 

Best,

 

Alexander Griesser

Head of Systems Operations

 

ANEXIA Internetdienstleistungs GmbH

 

E-Mail: AGriesser@anexia-it.com

Web: http://www.anexia-it.com

 

Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt

Geschäftsführer: Alexander Windbichler

Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

 

Von: andrei.borzenkov@ts.fujitsu.com [mailto:andrei.borzenkov@ts.fujitsu.com]
Gesendet: Donnerstag, 15. Dezember 2016 17:37
An: Alexander Griesser <AGriesser@anexia-it.com>
Cc: jordan slingerland <jordan.slingerland@gmail.com>; toasters@teaparty.net
Betreff: Re: AW: AW: AW: System attention LED

 

On the node that has LED on. If both are affected, you can do this one after another with usual takeover/giveback.

Отправлено с iPhone


15 дек. 2016 г., в 19:17, Alexander Griesser <AGriesser@anexia-it.com> написал(а):

Yah, read that – but what I’m unsure about: Do both nodes need to be halted at the same time (aka downtime for the customer) or can I do them one after the other?

 

Alexander Griesser

Head of Systems Operations

 

ANEXIA Internetdienstleistungs GmbH

 

E-Mail: AGriesser@anexia-it.com

Web: http://www.anexia-it.com

 

Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt

Geschäftsführer: Alexander Windbichler

Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

 

Von: andrei.borzenkov@ts.fujitsu.com [mailto:andrei.borzenkov@ts.fujitsu.com]
Gesendet: Donnerstag, 15. Dezember 2016 17:12
An: Alexander Griesser <AGriesser@anexia-it.com>
Cc: jordan slingerland <jordan.slingerland@gmail.com>; toasters@teaparty.net
Betreff: Re: AW: AW: System attention LED

 

In 7-Mode "halt -s" was known to clear stray alarm LED. Not sure what is equivalent in C-Mode.

 


Отправлено с iPhone


15 дек. 2016 г., в 15:46, Alexander Griesser <AGriesser@anexia-it.com> написал(а):

Hi,

 

the LED is still on and I guess it should have been fully charged by now if this would have been the issue.

So, any other ideas besides opening a case?

 

Regarding the FAS2240 I mentioned in my initial e-mail:

SP netapp1*> system fru led show 0

FRU LED ID 0 is off

SP netapp1*> system fru led show 1

FRU LED ID 1 is on

 

I did google a bit for this symptom and therefore updated the SP firmware to the latest compatible one for my ontap version (2.1.3P2), but that did not fix the issue.

Any fix for this symptom except for halting both nodes?

 

Best,

 

Alexander Griesser

Head of Systems Operations

 

ANEXIA Internetdienstleistungs GmbH

 

E-Mail: AGriesser@anexia-it.com

Web: http://www.anexia-it.com

 

Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt

Geschäftsführer: Alexander Windbichler

Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

 

Von: toasters-bounces@teaparty.net [mailto:toasters-bounces@teaparty.net] Im Auftrag von Alexander Griesser
Gesendet: Mittwoch, 14. Dezember 2016 23:29
An: jordan slingerland <jordan.slingerland@gmail.com>
Cc: toasters@teaparty.net
Betreff: AW: AW: System attention LED

 

Maybe that has changed with OnTap 9.1? I’m running 9.1RC2 here on this filer and not because I’m brave, but because it got shipped with it J

 

Alexander Griesser

Head of Systems Operations

 

ANEXIA Internetdienstleistungs GmbH

 

E-Mail: AGriesser@anexia-it.com

Web: http://www.anexia-it.com

 

Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt

Geschäftsführer: Alexander Windbichler

Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

 

Von: jordan slingerland [mailto:jordan.slingerland@gmail.com]
Gesendet: Mittwoch, 14. Dezember 2016 23:27
An: Alexander Griesser <AGriesser@anexia-it.com>
Cc: toasters@teaparty.net; Brad Thompson <brad.thompson877@gmail.com>
Betreff: Re: AW: System attention LED

 

Hmm, expected it to look like this listing charge voltage. Current and hours it can hold 

 

 


_______________________________________________
Toasters mailing list
Toasters@teaparty.net
http://www.teaparty.net/mailman/listinfo/toasters