If you can afford it, it might be worth a total system power cycle.
i.e. shut down both heads and all disks. wait 10-20 seconds.
Power on disks, then heads.

Sounds like something went screwy with during the hot-add.

--tmac

Tim McCarthy
Principal Consultant


          

        Clustered ONTAP                                                        Clustered ONTAP
 NCDA ID: XK7R3GEKC1QQ2LVD           RHCE6 110-107-141           NCSIE ID: C14QPHE21FR4YWD4
     Expires: 08 November 2014              Current until Aug 02, 2016         Expires: 08 November 2014



On Sat, Aug 3, 2013 at 8:43 PM, Alexander Griesser <ag@anexia.at> wrote:

Actually, it say to reseat all 48, I just pasted the message for one, sorry for not being precise about that.

 

[…]

 

               Node: robin

           Resource: Disk 0a.06.11

           Severity: Major

     Probable Cause: Disk 0a.06.11 does not have two paths to controller

                     robin but the containing disk shelf 6 does have two

                     paths. Disk 0a.06.11 may be faulty.

    Possible Effect: Access to disk 0a.06.11 via controller robin will be

                     lost with a single hardware component failure (e.g.

                     cable, HBA, or IOM failure).

Corrective Actions: 1. Reseat disk 0a.06.11 following the rules in the Installation and Service Guide.

                     2. Wait six minutes for the alert condition to clear.

                     3. If reseating disk 0a.06.11 fails to clear the alert condition, replace disk 0a.06.11.

                     4. Wait six minutes for the alert condition to clear.

                     5. Contact support personnel if the alert persists.

 

               Node: robin

           Resource: Disk 0a.06.10

           Severity: Major

     Probable Cause: Disk 0a.06.10 does not have two paths to controller

                     robin but the containing disk shelf 6 does have two

                     paths. Disk 0a.06.10 may be faulty.

    Possible Effect: Access to disk 0a.06.10 via controller robin will be

                     lost with a single hardware component failure (e.g.

                     cable, HBA, or IOM failure).

Corrective Actions: 1. Reseat disk 0a.06.10 following the rules in the Installation and Service Guide.

                     2. Wait six minutes for the alert condition to clear.

                     3. If reseating disk 0a.06.10 fails to clear the alert condition, replace disk 0a.06.10.

                     4. Wait six minutes for the alert condition to clear.

                     5. Contact support personnel if the alert persists.

 

48 entries were displayed.

 

The one I quoted was the last one, the last two are shown above and the message at the bottom, now in red, indicates 48 entries of this type and when I scroll up in the output of the filer, it has an alert message for all of the 48 new disks, that’s what puzzles me.

 

Bye,

 

Alexander Griesser

System-Administrator

 

ANEXIA Internetdienstleistungs GmbH

 

Telefon: +43-463-208501-320

Telefax: +43-463-208501-500

 

E-Mail: ag@anexia.at

Web: http://www.anexia.at

 

Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt

Geschäftsführer: Alexander Windbichler

Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

 

Von: tmac [mailto:tmacmd@gmail.com]
Gesendet: Sonntag, 04. August 2013 02:40
An: Alexander Griesser
Cc: chaim.rieger@gmail.com; toasters-bounces@teaparty.net; Toasters@teaparty.net


Betreff: Re: System status degraded after hot adding 2 DS4243 shelves

 

It did not say all 48 disks...just this:

 

Reseat disk 0a.06.10 following


--tmac

 

Tim McCarthy

Principal Consultant

 

          

 

        Clustered ONTAP                                                        Clustered ONTAP

 NCDA ID: XK7R3GEKC1QQ2LVD           RHCE6 110-107-141           NCSIE ID: C14QPHE21FR4YWD4

     Expires: 08 November 2014              Current until Aug 02, 2016         Expires: 08 November 2014

 

On Sat, Aug 3, 2013 at 8:15 PM, Alexander Griesser <ag@anexia.at> wrote:

All LEDs green, all SAS ports show link, even the controller LEDs are both green which is what puzzled me a bit, since it should light up in orange, shouldn't it?


Alexander Griesser
System-Administrator

ANEXIA Internetdienstleistungs GmbH

Telefon: +43-463-208501-320
Telefax: +43-463-208501-500

E-Mail: ag@anexia.at
Web: http://www.anexia.at

Anschrift Hauptsitz Klagenfurt: Feldkirchnerstraße 140, 9020 Klagenfurt
Geschäftsführer: Alexander Windbichler
Firmenbuch: FN 289918a | Gerichtsstand: Klagenfurt | UID-Nummer: AT U63216601

-----Ursprüngliche Nachricht-----
Von: chaim.rieger@gmail.com [mailto:chaim.rieger@gmail.com]
Gesendet: Sonntag, 04. August 2013 02:12
An: Alexander Griesser; toasters-bounces@teaparty.net; Toasters@teaparty.net
Betreff: Re: System status degraded after hot adding 2 DS4243 shelves


The return cable from the last shelf to your defgraded filer is either bad, not connected properly or the slot is bad

Are all the led's green ?
Sent via BlackBerry from T-Mobile

-----Original Message-----
From: Alexander Griesser <ag@anexia.at>
Sender: toasters-bounces@teaparty.net
Date: Sat, 3 Aug 2013 23:44:20
To: Toasters@teaparty.net<Toasters@teaparty.net>
Subject: System status degraded after hot adding 2 DS4243 shelves

_______________________________________________
Toasters mailing list
Toasters@teaparty.net
http://www.teaparty.net/mailman/listinfo/toasters



_______________________________________________
Toasters mailing list
Toasters@teaparty.net
http://www.teaparty.net/mailman/listinfo/toasters